Filter
Top Products
26
|
KDC-U7046BT/ KDC-U7046BTL/ KDC-U6046/ KDC-U6046L
Bluetooth Setup
Function of KDC-U7046BT/ KDC-U7046BTL/ KCA-BT200 (Optional Accessory)
Registering Bluetooth device
To make your Bluetooth device (cell-phone) usable
with this unit, you need to register it (pairing). You
can register up to five Bluetooth devices to this unit.
When registering from Bluetooth devices
1 Turn on the this unit.
2 Start registering a unit by operating the
Bluetooth device
By operating the Bluetooth device, register the
hands-free unit (pairing). Select “KENWOOD
BT CD/R-4P1” or “KCA-BT200” from the list of
connected units.
3 Enter a PIN code
Input the PIN code registered as mentioned in
<Registering PIN Code> (page 27).
Check that registration is complete on the
Bluetooth device.
4 By operating the Bluetooth device, start hands-
free connection.
When registering from this unit
1 Enter Bluetooth mode
KDC-U7046BT KDC-U7046BTL
Press the [ ] button.
KDC-U6046 KDC-U6046L
Press the [FNC] button for at least 1 second.
“BT MODE” is displayed.
2 Enter Function setting mode
Press the [FNC] button.
3 Select Bluetooth device registration mode
The item can be selected and determined as
follows.
”Settings” ➜ “Detailed Settings” ➜ “Device
Regist.”
To select the item, turn the Control knob. To
determine the item, press the [ENTER] button.
Search for the Bluetooth device.
When search is completed, “Finished” is displayed.
4 Select the Bluetooth device
Turn the Control knob to select desired
Bluetooth device, and then press the [ENTER]
button.
KDC-U7046BT KDC-U7046BTL
When “Paring Success” is displayed, PIN code input
(steps 5 and 6) is not required. When “Pin Code NG”
is displayed, press the [ENTER] button. Then enter
the PIN code (steps 5 and 6).
KDC-U6046 KDC-U6046L
Input the PIN code (steps 5 and 6).
5 Input the PIN code
Operation type Operation
Select the numbers. Turn the Control knob.
Move to the next digit. Push the Control knob towards right.
Delete the last digit. Push the Control knob towards left.
6 Transmit the PIN code
Press the [ENTER] button.
If “Pairing Success” is displayed, registration is
complete.
7 Return to the device list
Press the [ENTER] button.
8 Exit Bluetooth mode
Press the [SRC] button.
⁄
• This unit allows up to eight digits to be input for a PIN code.
If a PIN code cannot be input from this unit, it can be input
from the Bluetooth device.
• If there are 5 or more Bluetooth devices registered, you
cannot register a new Bluetooth device.
• If the error message appears even though the PIN code is
correct, try <Registering Special Bluetooth device> (page 26).
Registering Special Bluetooth device
Allow registration of a special device that cannot be
registered normally (pairing).
1 Enter Bluetooth mode
KDC-U7046BT KDC-U7046BTL
Press the [ ] button.
KDC-U6046 KDC-U6046L
Press the [FNC] button for at least 1 second.
“BT MODE” is displayed.
2 Enter Function setting mode
Press the [FNC] button.
3 Select Special device registration mode
The item can be selected and determined as
follows.
”Settings” ➜ “Detailed Settings” ➜ “SPCL DVC
Select”
To select the item, turn the Control knob. To
determine the item, press the [ENTER] button.
4 Select a device name
Turn the Control knob to select desired device