Filter
Top Products
21
Sound adjustments
Adjusting speaker output level
• SUBWFR LVL (subwoofer output level),
• FRONT L LVL (left front speaker output level),
• FRONT R LVL (right front speaker output level),
• CENTER LVL (center speaker output level),
• SURR L LVL (left surround speaker output level),
• SURR R LVL (right surround speaker output level)
You can adjust the speaker output levels.
Adjust all the speakers’ output levels so that you can listen sounds
from all speakers at the same level.
• Once you have made an adjustment, it is memorized for each
source.
Adjustable range: –10 (dB) to +10 (dB) (in 1 step intervals)
Initial setting: 0 (dB) for all speakers
NOTES
• If you have selected “NO” for a speaker (see page 16), the
output level for the corresponding speaker is not adjustable.
• While using headphones, you can adjust only the left and right
front speakers’ output level.
• If you change one of these settings (except the subwoofer
output level) manually, the distance and output level set
manually will be applied instead of those set by using Smart
Surround Setup.
Adjusting the sound parameters for
the Surround/DSP modes
You can adjust the Surround/DSP sound parameters to your
preference.
• For details about the Surround/DSP modes, see pages 25 to 29.
Adjusting the effect level for DSP modes—EFFECT
This setting is available only when one of the DSP modes (except
ALL CH ST.) is in use. To activate DSP mode, see pages 28 and
29.
• Once you have made an adjustment, it is memorized for each
DSP mode.
Adjustable range: 1 to 5 (in 1 step intervals)
Initial setting: EFFECT 3
As the number increases, the effect becomes stronger.
Normally, select “3.”
Adjusting the panorama control for Pro Logic II
Music—PANORAMA
This setting is available only when Pro Logic II Music is in use. To
activate Pro Logic II Music, see pages 28 and 29.
• Once you have made an adjustment, it is memorized until you
change the setting.
• You cannot use the remote control for this setting.
PANORAMA ON Select to add “wraparound” sound effect with
side-wall image.
PANORAMAOFF Select to listen to originally recorded sound.
Initial setting: PANORAMAOFF
Adjusting the center tone—CENTER TONE
This setting is available when one of the Surround/DSP modes is
in use.
• If you have set “CENTER SPK” to “NO” (see page 16), the
center tone is not adjustable.
• This setting is common to all Surround modes, and is
memorized separately for DSP modes.
Adjustable range: 1 to 5 (in 1 step intervals)
Initial setting: CNT TONE 3
As the number increases, the dialogue becomes stronger.
Normally, select “3.”
• When the center tone is set to other than “CNT TONE 3,” the
C.TONE indicator lights up on the display.
From the remote control:
EQ
LPCM L
LS SB RS
S . WFR
PL
NEO : 6
DSP 3D
LFE
C R
DOLBY D
DTS AAC
96 / 24
AUTO SR
C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST SLEEP
AUTO MUTING AUTO MODE
ATT
HP
MHz
kHz
LCR
LS RS
(Left front speaker) (Right front speaker)
(Left surround speaker)
SW
(Subwoofer) (Right surround speaker)
(Center speaker)
From the remote control:
To adjust the effect level:
Press SOUND, then press EFFECT
repeatedly.
To adjust the center tone:
Press SOUND, then press C.TONE
repeatedly.
NOTE
After pressing SOUND, the numeric
buttons work for sound adjustments. To
use the numeric buttons to operate your
target source, press the corresponding
source selecting button before operation;
otherwise, the remote control may not
work as you intend.
1
Press TEST TONE to check the speakers’ output
balance.
“TEST L” starts flashing on the display, and a test tone
comes out of the speakers in the following order:
2
Adjust the speaker output levels.
When you press the level adjustment buttons
corresponding to each speaker once, the current level for
the speaker appears on the display, and the test tone
comes out of the speaker.
EX.: When adjusting output level for the center speaker:
Press CENTER +/–.
The test tone comes out of the center speaker.
If no adjustment is done for about 4 seconds, the test tone
comes out of the next speaker.
3
Press TEST TONE again to stop the test tone.
NOTES
• You can adjust the speaker output levels without the test
tone.
• No test tone is available when the HEADPHONE (or 3D
HEADPHONE) mode is in use.
EN20-22RXE11S[US_UX]2.p65 06/12/2004, 21:3821