Filter
Top Products
18
English
In this case, set the distance as follows:
Left front speaker (L): “FRONT L <3.0m> (10ft)”
Right front speaker (R): “FRONT R <3.0m> (10ft)”
Center speaker (C): “CENTER <3.0m> (10ft)”
Left surround speaker (LS): “SURR L <2.7m> (9ft)”
Right surround speaker (RS): “SURR R <2.7m> (9ft)”
Left surround back speaker (SBL) : “SBACK L <2.4m> (8ft)”
Right surround back speaker (SBR) : “SBACK R <2.4m> (8ft)”
NOTES
• You cannot set the speaker distance for the speakers you have
set to “NO.”
• If you have selected “
<1SPK>” for “S BACK OUT” (see page
17), “S BACK DIST” appears instead of “S BACK L DIST” and
“S BACK R DIST.”
Setting the speaker distance
The distance from your listening point to the speakers is one of
the important elements to obtain the best possible sound effect
from the Surround/DSP modes.
By referring to the speaker distance, the receiver automatically
sets the delay time of the sound through each speaker so that
sounds through all the speakers can reach you at the same time.
If you have used Quick Speaker Setup on page 15, this setting is
not required.
7 Measuring unit—DIST UNIT
Select which measuring unit you use.
D UNIT <meter>Select to set the distance in meters.
D UNIT <feet> Select to set the distance in feet.
Initial setting: D UNIT <meter>
7 Speaker distance—
FRONT L DIST (for the left front speaker),
FRONT R DIST (for the right front speaker),
CENTER DIST (for the center speaker),
SURR L DIST (for the left surround speaker),
SURR R DIST (for the right surround speaker),
S BACK L DIST (for the left surround back speaker),
S BACK R DIST (for the right surround back speaker)
Adjustable range: 0.3 m to 9.0 m in 0.3 m intervals
(1 ft to 30 ft in 1 ft intervals)
Initial setting: 3.0 m (10 ft) for all speakers
Activating the EX/ES/PLIIx setting—
EX/ES/PLIIx
Depending on this setting, available Surround modes for digital
multi-channel software vary—EX/ES/PLIIx reproduction or 5.1-
channel reproduction. Select an appropriate setting for your
enjoyment.
• For details about relation between EX/ES/PLIIx setting and
available Surround mode, see page 30.
• To activate the Surround mode, see page 31.
<AUTO> According to the incoming signal, an appropriate
Surround mode is applied.
• For Dolby Digital Surround EX and DTS-ES
software, 7.1-channel reproduction is applied*.
• For other multi-channel (4 channel or more)
encoded software, 5.1-channel reproduction is
applied.
<ON> Select to apply 7.1-channel reproduction to both
5.1-channel and 6.1-channel encoded software.
<PLIIx MOVIE> Select to apply PLIIx MOVIE reproduction to
both 5.1-channel and 6.1-channel encoded
software.
<PLIIx MUSIC>Select to apply PLIIx MUSIC reproduction to
both 5.1-channel and 6.1-channel encoded
software.
<OFF> Select to cancel the EX/ES/PLIIx reproduction.
Initial setting:
<AUTO>
* For some Dolby Digital Surround EX software, Dolby Digital 5.1-
channel reproduction (“DOLBY DIGITAL”) may be applied even
though you have selected “
<AUTO>.” In this case, select
“
<ON>” to apply “DOLBY D EX.”
From the remote control:
Press EX/ES/PLIIx repeatedly to select either one of the
above.
NOTES
• When “SURROUND SPK” is set to “NO” (see page 17), this
function is not available.
• When “S BACK SPK” is set to “NO” (see page 17), the Virtual
Surround Back (see page 30) is applied for EX/ES/PLIIx
reproduction.
4
7
10
5
8
0
6
9
10
C
L
R
LS
RS
SBL
SBR
2.1 m
(7 ft)
2.4 m
(8 ft)
2.7 m
(9 ft)
3.0 m
(10 ft)
3.3 m
(11 ft)