Filter
Top Products
43
English
Turntable
After pressing PHONO (with the remote control mode selector set to
“AUDIO/TV/VCR”), you can perform the following operations on a
turntable:
PLAY: Starts playing.
STOP: Stops operations.
Cassette deck
After pressing TAPE/MD or TAPE CONTROL (with the remote
control mode selector set to “AUDIO/TV/VCR”), you can perform
the following operations on a cassette deck:
PLAY: Starts playing.
11
11
1: Fast winds the tape from right to left.
¡¡
¡¡
¡: Fast winds the tape from left to right.
STOP: Stops operations.
PAUSE: Pauses playing. To release it, press PLAY.
¶ REC: Press this button with the PLAY button to start
recording.
Press this button with the PAUSE button to enter
recording pause.
MD recorder
After pressing TAPE/MD or TAPE CONTROL (with the remote
control mode selector set to “AUDIO/TV/VCR”), you can perform
the following operations on the MD recorder:
PLAY: Starts playing.
4: Returns to the beginning of the current (or previous)
track.
¢: Skips to the beginning of the next track.
STOP: Stops playing.
PAUSE: Pauses playing. To release it, press PLAY.
¶ REC: Press this button with the PLAY button to start
recording.
Press this button with the PAUSE button to enter
recording pause.
Note:
You can use either TAPE/MD button or the TAPE CONTROL button to
activate the buttons listed above. If you press TAPE/MD, the playing
source also changes. On the other hand, if you press TAPE
CONTROL, the playing source does not change.
IMPORTANT:
To operate JVC’s video components using this remote control:
• Aim the remote control directly at the remote sensor on the VCR,
DVD player or TV, not on the receiver.
• Some JVC VCRs can accept two types of the control signals —
remote code “A” and “B.” Before using this remote control, make
sure that the remote control code of the target VCR is set to code
“A.”
VCR
You can always perform the following operations (with the remote
control mode selector set to “AUDIO/TV/VCR”):
VCR 1 : Turns on or off the VCR.
After pressing VCR 1 or VCR 1 CONTROL (with the remote
control mode selector set to “AUDIO/TV/VCR”), you can perform
the following operations on the VCR:
1 – 9, 0: Selects the TV channels on VCR.
PLAY: Starts playing.
1: Rewinds a tape.
¡: Fast winds a tape.
STOP: Stops operations.
PAUSE: Pauses playing. To release it, press PLAY.
¶ REC: Press this button with the PLAY button to start
recording.
Press this button with the PAUSE button to enter
recording pause.
CHANNEL +/–: Changes the TV channels on the VCR.
Note:
You can use either VCR 1 button or the VCR 1 CONTROL button to
activate the buttons listed above. If you press VCR 1, the playing
source also changes. On the other hand, if you press VCR 1
CONTROL, the playing source does not change.
DVD player
After pressing DVD or DVD MULTI (with the remote control mode
selector set to “AUDIO/TV/VCR”), you can perform the following
operations on a DVD player:
PLAY: Starts playing.
4: Returns to the beginning of the current (or previous) track.
¢: Skips to the beginning of the next track.
STOP: Stops playing.
PAUSE: Stops playing temporarily. To release it, press PLAY.
After pressing DVD or DVD
MULTI, these buttons can be used
for the DVD menu operations.
Note:
For detailed menu operations, refer to the
instructions supplied with the discs or the
DVD player.
TV
You can always perform the following operations (with the remote
control mode selector set to “AUDIO/TV/VCR”):
TV/CATV/DBS
: Turns on or off the TV.
TV VOL +/–: Adjusts the volume.
TV/VIDEO: Sets the input mode (either TV or VIDEO).
After pressing TV/DBS (with the remote control mode selector set
to “AUDIO/TV/VCR”), you can perform the following operations
on a TV:
CHANNEL +/–: Changes the channels.
1 – 9, 0, 100+: Selects the channels.
RETURN: Alternates between the previously selected channel
and the current channel.
CNTR
TEST REAR-L
REAR-R
23
456
8
MENUMENU
ENTERENTER
EN42_52.RX-889P[US, UB]/f 99.4.12, 5:37 PM43