Filter
Top Products
8
English
Digital connections
This receiver is equipped with three DIGITAL IN terminals — one
digital coaxial terminal and two digital optical terminals.
You can connect any component to any one of the digital terminals
using the digital coaxial cable (not supplied) or digital optical cable
(not supplied).
IMPORTANT:
• When connecting the DVD player or the DBS tuner using the digital
terminal, you also need to connect it to the video jack (either
composite video terminal or S-video terminal) on the rear. Without
connecting it to the video jack, you can view no playback picture.
• After connecting the components using the DIGITAL IN terminals,
set the following correctly if necessary.
– Select the digital input mode correctly. For details, see “Selecting
the Analog or Digital Input Mode” on page 13.
– Set the digital input (DIGITAL IN) terminal setting correctly. For
details, see “Digital Input (DIGITAL IN) Terminal Setting” on page
13.
DVD
DIGITAL IN
DIGITAL 3 (CD)
DIGITAL 2 (DVD)
DIGITAL 1 (DBS)
PCM / DOLBY DIGITAL
MPEG / DTS
DBS
Before connecting a digital
optical cable, unplug the
protective plug.
MD recorder
DVD player
DBS tuner
CD player
Notes:
• When shipped from the factory, the DIGITAL IN terminals has been
set for use with the following components.
– DIGITAL 1 (coaxial): For DBS tuner
– DIGITAL 2 (optical): For DVD player
– DIGITAL 3 (optical): For CD player
• When you want to operate the CD player or MD recorder using the
COMPU LINK remote control system, connect the target
component also as described in “Analog connections” (see pages 5
and 6).
Connecting the Power Cord
Before plugging the receiver into an AC outlet, make sure that all
connections have been made.
Plug the power cord into an AC outlet.
Keep the power cord away from the connecting cables and the
antenna. The power cord may cause noise or screen interference. We
recommend that you use a coaxial cable to connect the antenna,
since it is well-shielded against interference.
Notes:
• Except for Hong Kong: If the wall outlet does not match the AC
plug, use the supplied AC plug adaptor.
• The preset settings such as preset channel and sound adjustment
may be erased in a few days in the following cases:
– When you unplug the power cord.
– When a power failure occurs.
CAUTIONS:
• Do not plug in before setting the voltage selector switch on the rear
of the unit and all connection procedures are complete.
• Do not touch the power cord with wet hands.
• Do not pull on the power cord to unplug the cord. When unplugging
the cord, always grasp the plug so as not to damage the cord.
Putting Batteries in the Remote Control
Before using the remote control, put two supplied batteries first.
When using the remote control, aim the remote control directly at
the remote sensor on the receiver.
1. On the back of the remote control, remove the
battery cover.
2. Insert batteries. Make sure to match the polarity:
(+) to (+).
3. Replace the cover.
If the range or effectiveness of the remote control decreases, replace
the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.
CAUTION:
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity: (+)
to (+).
• Use the correct type of batteries. Batteries that look similar may
differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
When the component has a digital
optical output terminal, connect it to the
DIGITAL 2 (DVD) or DIGITAL 3 (CD)
terminal, using the digital optical cable
(not supplied).
When the component has a digital
coaxial output terminal, connect it to the
DIGITAL 1 (DBS) terminal, using the
digital coaxial cable (not supplied).
1
3
2
EN01-08.RX-889P[US, UB]/f 99.4.12, 5:29 PM8