Filter
Top Products
17
English
Speaker size
Register the sizes of all the connected speakers.
• When you change your speakers, register the information about
the speakers again.
1
Press SETTING repeatedly until “FRNT
SP (Front Speaker),” “CNTR SP (Center
Speaker)” or “REAR SP (Rear Speaker)”
(with the current setting)* appears on the display.
* “LARGE” is the initial setting for the front speakers and
“SMALL” is for the center and rear speakers. If you have
already changed the setting, another size will be shown.
2
Press CONTROL UP 5/DOWN ∞ to
select the appropriate item about the
speaker selected in the above step.
• Each time you press the button, the display
changes as follows:
LARGE : Select this when the speaker size is relatively large.
(See “Notes” below.)
SMALL : Select this when the speaker size is relatively small.
(See “Notes” below.)
NONE : Select this when you have not connected a speaker.
(Not selectable for the front speakers)
3
Repeat steps
1
and
2
to select the appropriate
items for other speakers.
Notes:
• Keep the following comment in mind as reference when adjusting.
– If the size of the cone speaker unit built in your speaker is greater
than 12 cm (4
3
/
4
inches), select “LARGE,” and if it is smaller than
12 cm (4
3
/
4
inches), select “SMALL.”
• If you have selected “NO” for the subwoofer setting, you can only
select “LARGE” for the front speaker setting.
• If you have selected “SMALL” for the front speaker setting, you
cannot select “LARGE” for the center and rear speaker settings.
Speaker distance
Register the unit you use, then the speaker distance from your
listening point.
• If you have set the unit before, start from step
3
.
• Speaker distance is not valid for the DVD MULTI playback mode.
T SETTING
3.0 m
(10 feet)
Left front
speaker
Right front
speaker
Right rear
speaker
Left rear
speaker
Center speaker
2.7 m
(9 feet)
2.4 m
(8 feet)
2.1 m
(7 feet)
Example: In this case,
set “FRNT DIS” to “3.0m” or “10FT,”
set “CNTR DIS” to “2.7m” or “9FT,” and
set “REAR DIS” to “2.4m” or “8FT.”
Note:
If you have selected “NONE” for the center and rear speakers setting,
you cannot set the speaker distance for the center and rear speakers.
L C
S.WFR
LS RS
CH-
S
LFE
SPK
DIGITAL AUTO
LINEAR PCM
1
R
LARGE
SMALL
NONE
CONTROL
DOWN UP
T SETTING
1
Press SETTING repeatedly until “UNIT”
(with the current setting)* appears on the
display.
* “METER” is the initial setting. If you have already changed
the setting, “FEET” will be shown.
2
Press CONTROL UP 5/DOWN ∞ to
select the unit.
• Each time you press the button, the setting
alternates between “METER” and “FEET.”
METER : Speaker distance is shown in meters.
FEET : Speaker distance is shown in feet.
3
Press SETTING repeatedly until “FRNT
DIS (Front distance),” “CNTR DIS
(Center distance)” or “REAR DIS (Rear
distance)” (with the current setting)*
appears on the display.
• The display shows the current setting in the unit selected in
step
2
.
* “3.0m” is the initial setting for meter and “10FT” is for feet. If
you have already changed the setting, another value will be
shown.
4
Press CONTROL UP 5/DOWN ∞ to
select the appropriate speaker distance.
• If you select “METER” in step
2
, the value is
changed from “0.3m” to “9.0m” by 0.3 m step.
• If you select “FEET” in step
2
, the value is
changed from “1FT” to “30FT” by 1 foot step.
CONTROL
DOWN UP
CONTROL
DOWN UP
ST SETTING
L C
S.WFR
LS RS
CH-
S
LFE
SPK
DIGITAL AUTO
LINEAR PCM
1
R
EN10-22.RX-7520V[C]f.pm5 02.2.14, 4:32 PM17