Filter
Top Products
29
English
Sound control section (Amplifier)
You can always perform the following operations:
SURROUND: Turns on or off the Surround modes —
Dolby Pro Logic, Dolby Digital, and DTS
Digital Surround.
SURROUND MODE: Selects the DSP modes.
After pressing SOUND, you can perform the following operations:
SUBWOOFER – / +: Adjusts the subwoofer output level.
CENTER – / +: Adjusts the center speaker output level.
REAR•L – / +: Adjusts the left rear speaker output level.
REAR•R – / +: Adjusts the right rear speaker output level.
EFFECT: Selects the effect level.
TEST: Turns on or off the test tone output.
Note:
After adjusting sounds, press the corresponding source selecting
button or CD-DISC to operate your target source by using the 10
keys; otherwise, the 10 keys cannot be used for operating your target
source.
Turntable
After pressing PHONO, you can perform the following operations
on a turntable:
3: Starts playing.
7: Stops operations.
CD player
After pressing CD, you can perform the following operations on the
CD player:
33
33
3: Starts playing.
44
44
4: Returns to the beginning of the current (or
previous) track.
¢¢
¢¢
¢: Skips to the beginning of the next track.
77
77
7: Stops playing.
88
88
8: Pauses playing. To release it, press
33
33
3.
1 – 10, +10: Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
Operating JVC’s Audio/Video Components
You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC
components are preset in the remote control.
IMPORTANT:
To operate JVC’s audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK-3 (SYNCHRO) jacks (see page 26) in addition to the
connections using cables with RCA pin plugs (see page 5).
• Aim the remote control directly at the remote sensor on the receiver.
• If you use the buttons on the front panel to choose a source, the
remote control will not operate that source. To operate a source with
the remote control, the source must be selected using source
selecting buttons on the remote control.
• To operate the cassette deck or MD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 11.)
• Refer also to the manuals supplied with your components.
Tuner
After pressing FM/AM, you can perform the following operations:
FM/AM: Alternates between FM and AM.
1 – 10, +10: Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then 10.
1
7
1
RM-SRX6000J REMOTE CONTROL
SURROUND
SURROUND
MODE
SOUND
TV/VIDEO
CD-DISC
321
5
– SUBWOOFER +TEST
6
54
EFFECT
– CENTER +
5
98
– REAR•L + – VCR CH +
5
TV
VCR
AUDIO
SLEEP
+10
10
– REAR•R +
MENU
ENTER
5
TAPE/MD
PHONO FM/AM
MUTING
CD
TV SOUND/DBS
VCR
ANALOG/DIGITAL
TV VOL
TV CH
DVD
–
–
VCR CH
+
+
VOLUME
£
POWER
8
+
–
7/P
EN27_33.RX-6000V[J] 99.12.14, 4:00 PM29