Harman-Kardon AVR 3000 Stereo Receiver User Manual


 
REMOTE CONTROL FUNCTIONS 13
J
Direct Button: Press this button when the
tuner is in use to start the sequence for direct
entry of a station’s frequency. After pressing the
button simply press the proper Numeric Keys
H
to select a station (See page 31 for more
information on the tuner).
K
Tuning Up/Down:When the tuner is in use,
these buttons will tune up or down through the
selected frequency band. If the Tuner Mode but-
ton
I
has been pressed or the Band button
@
on the front panel was held pressed so that
the AUTO indicator
X
is illuminated, pressing
either of the buttons will cause the tuner to seek
the next station with acceptable signal strength
for quality reception.When the AUTO indicator
X
is NOT illuminated, pressing these buttons will
tune stations in single-step increments. (See page
31 for more information.)
L
OSD Button: Press this button to activate
the On Screen Display (OSD) system used to set
up or adjust the AVR 3000’s parameters.
M
Macro Buttons: Press these buttons
to store or recall a “Macro”, which is a
pre-programmed sequence of commands
stored in the remote. (See page 37 for more
information on storing and recalling macros.)
N
Transport Buttons: These buttons do not
have any functions for the AVR, but they may be
programmed for the forward/reverse play opera-
tion of a wide variety of CD or DVD players, and
audio or video- cassette recorders. (See page 36
for more information on programming the
remote.)
O
Skip Up/Down Buttons: These buttons
do not have a direct function with the AVR
3000, but when used with a compatibly pro-
grammed CD or DVD changer they will change
the tracks on the disc currently being played in
the changer.
P
RDS Select Button: Press this button to
display the various messages that are part of the
RDS data system of the AVR 3000’s tuner. (See
page 32 for more information on RDS).
Q
Preset Up/Down: When the tuner is in
use, press these buttons to scroll through the
stations programmed into the AVR 3000’s mem-
ory. When CD or DVD is selected using the
Input Selector button
4
, these buttons may
function as Slow Fwd/Rev (DVD) or ”+10” (CD).
R
Clear Button: Press this button to clear
incorrect entries when using the remote to
directly enter a radio station’s frequency.
S
Memory Button: Press this button to enter
a radio station into the AVR 3000’s preset
memory. After pressing the button the MEMORY
indicator
U
will flash; you then have five sec-
onds to enter a preset memory location using
the Numeric Keys
H
. (See page 31 for more
information.)
T
Delay/Prev Ch.: Press this button to begin
the process for setting the delay times used by
the AVR 3000 when processing surround sound.
After pressing this button, the delay times are
entered by pressing the Set button
F
and
then using the
/
¤
buttons
D
to change the
setting. Press the Set button again to complete
the process. (See page 21 for more information.)
U
Button: Press this button to change a set-
ting or selection when configuring many of the
AVR’s settings.
V
Speaker Select: Press this button to
begin the process of configuring the AVR
3000’s Bass Management System for use with
the type of speakers used in your system. Once
the button has been pressed, use the
/
¤
but-
tons
D
to select the channel you wish to set
up. Press the Set button
F
and then select
the speaker type (see page 19 for more infor-
mation.)
W
Spare Button: This button does not have
any function for the operation of the AVR3000,
but it can turn on/off the Multiroom system on
other Harman Kardon AV-receivers with that fea-
ture and the Sub-function on DVD players.
X
Volume Up/Down: Press these buttons to
raise or lower the system volume.
Y
TV/Video Button: This button does not
have a direct function on the AVR 3000, but
when used with a compatibly programmed VCR,
DVD or satellite receiver that has a “TV/Video”
function, pressing this button will switch
between the output of the player or receiver and
the external video input to that player. Consult
the Owner’s Manual for your specific player or
receiver for the details of how it implements this
function.
Z
SPL Indicator Select: This button acti-
vates the AVR 3000’s EzSet function to quickly
and accurately calibrate the AVR 3000’s output
levels. Press and hold the button for three sec-
onds and then release it. Note that the Test Tone
will begin circulating, and the Program
Indicator
2
will change colors. During this
sequence, EzSet will automatically adjust the
output levels for all channels until they are
equal, as shown by the Program Indicator
lighting green for each channel. (See page 23
for more information on EzSet.)
a
6-Ch. Direct Input: Press this button to
select the component connected to the 6-Ch.
Direct Input
8
as the source
b
Mute: Press this button to momentarily
silence the AVR 3000 or TV set being controlled,
depending on which device has been selected.
When the AVR 3000 remote is being programmed
to operate another device, this button is pressed
with the Input Selector button
4
to begin
the programming process. (See page 36 for more
information on programming the remote.)
NOTE: As any of the remote buttons pressed is
active with the device selected, the correspon-
ding Selector button
45
will briefly flash
red to confirm your selection.
Remote Control Functions