Filter
Top Products
FRONT-PANEL INFORMATION DISPLAY 7
FRONT-PANEL INFORMATION DISPLAY
MEM PRESET
SLEEP
AUTOANALOGCOAX 123OPT 123DTS
PCM
TUNED ST
D PL II 3ST OSD DSP VMAx NF LOGIC 7 CM
KHz
dB
MHz
NIGHT
LR
C
SL SR
LFE
D
A
K
S RTUV Q PO M L
B
C D E F G H I J
N
A Bitstream Indicators
B DTS Mode Indicator
C Dolby Digital Indicator
D Dolby Pro Logic II Indicator
E Dolby 3 Stereo/Stereo Indicator
F OSD Indicator
G DSP Mode Indicator
H VMAx Mode Indicators
I Logic 7 Mode Indicators
J Preset Number/Sleep Timer
K Night Mode Indicator
L Speaker/Channel Input Indicators
M Preset Indicator
N Sleep Indicator
O Memory Indicator
P Stereo Indicator
Q Tuned Indicator
R Auto Indicator
S Main Information Display
T Analog Input Indicator
U Coaxial Digital Input Indicators
V Optical Digital Input Indicators
A Bitstream Indicators: When the input is a digital
source, one of these indicators will light to display the spe-
cific type of data signal in use.
B DTS Mode Indicator: This indicator lights when a
DTS-encoded source is playing and DTS Surround
decoding is in use.
C Dolby Digital Indicator: This indicator lights
when a Dolby Digital source is being played and Dolby
Digital surround decoding is in use.
D Dolby Pro Logic II Indicator: This indicator lights
when the Dolby Pro Logic II mode has been selected.
• It is possible to see the Dolby Pro Logic II indicator
lit simultaneously with the Dolby Digital indicator,
even though the Dolby Digital surround mode has
been selected. This is due to the specifications for
Dolby Digital pro
cessing, which require that the Dolby
Pro Logic II
mode be used any time a two-channel
Dolby signal is detected.
• If you desire 5.1-channel audio, check the audio
settings in the menus for both your DVD player and
your DVD disc to make sure that a 5.1-channel
Dolby Digital soundtrack is available and has been
selected.
E Dolby 3 Stereo/Stereo Indicator: The entire
indicator lights when the Dolby 3 Stereo mode has
been selected. When the surround modes are turned
off so that two-channel stereo playback is in use, only
the “ST” indicator will light.
F OSD Indicator: When the On Screen Display
(OSD) system is in use, this indicator lights to remind
you that the other indicators in this display do not
function when the OSD is being used.
G DSP Mode Indicator: This indicator lights when
any of the surround modes created by Digital Signal
Processing, or DSP, are in use. These modes include
Hall 1, Hall 2, the Theater Mode and 5-Channel
Stereo.
H VMAx Mode Indicators: These
light when the
VMAx mode is in use. VMAx F
appears when the
Far Field VMAx mode is selected; VMAx N appears
when the Near Field VMAx mode is selected. (See
page 25 for a description of the VMAx modes.)
I Logic 7 Mode Indicators: These indicators light
when the Logic 7 mode is in use. LOGIC 7C
appears for the Cinema version; LOGIC 7M
appears for the Music version of Logic 7. (See page
25 for a description of the Logic 7 modes.)
J Preset Number/Sleep Timer: When the tuner is
in use, these numbers indicate the specific preset
memory location in use. (See page 28 for more infor-
mation on preset stations.) When the Sleep function is
in use, these numbers show how many minutes
remain before the unit goes into the Standby mode.
(See page 24 for information on the Sleep function.)
K Night Mode Indicator: This lights when the
AVR 225 is in the Night mode, which preserves the
dynamic range of digital program material at low vol-
ume levels. This mode is only available with specially
encoded Dolby Digital sources. (See page 27 for a
description of the Night mode.)
L Speaker/Channel Input Indicators: These indica-
tors are multipurpose, indicating either the speaker type
selected for each channel or the incoming data-signal
configuration. The left, center, right, right surround and
left surround speaker indicators are composed of three
boxes, while the subwoofer is a single box.The center
box lights when a “Small” speaker is selected, and the
two outer boxes light when “Large” speakers are
selected.When none of the boxes are lit for the center,
surround or subwoofer channels, no speaker has been
assigned to one of those positions. (See page 19 for
more information on configuring speakers.) The letters
inside each of the center boxes display active input
channels. For standard analog inputs, only the L and R
will light, indicating a stereo input.When a digital source
is playing, the indicators will light to display the channels
being received at the digital input.When the letters
flash, the digital input has been interrupted. (See page
27 for more information on the Channel Indicators.)
M Preset Indicator: This indicator lights when the
tuner is in use to show that the Preset Number/
Sleep Timer J is showing the station’s preset
memory number. (See page 28 for more information
on tuner presets.)