Filter
Top Products
Volume Punch-Through
The AVR 225’s remote may be programmed to oper-
ate the Volume Control and Mute func-
tions of either the TV or the AVR 225 in conjunction
with any of the devices controlled by the remote. For
example, since the AVR 225 will likely be used as the
sound system for TV viewing, you may wish to have
the AVR 225’s volume activated, although the remote
is set to run the TV. Either the AVR 225 or TV volume
control may be associated with any of the remote’s
devices.To program the remote for Volume Punch-
Through, follow these steps:
1. Press the Input Selector e for the unit you will
be using (e.g.,TV) when you wish to have Volume
Punch-Through to your audio system active and the
Mute Button at the same time until the red
light appears under the Input Selector e and the
Program/SPL Indicator c flashes amber.
2. Press the Volume Up Button and note that
the Program/SPL Indicator c will stop flashing
and stay amber.
3. Press either the AVR Selector f or the Input
Selector e, depending on which system’s
volume control you wish to have attached for the
punch-through mode.The Program/SPL Indicator
c will blink green three times and then go out to
confirm the data entry.
Example: To have the AVR 225’s volume control
activated even though the remote is set to control
the TV, first press the VID2/TV Input Selector
e and the Mute Button at the same time.
Next, press the Volume Up Button , followed
by the AVR Selector f.
NOTE: Should you wish to return the remote to the
original configuration after entering a Volume Punch-
Through, you will need to repeat the steps shown
above. However, press the same Input Selector in
Steps 1 and 3.
Channel Control Punch-Through
The AVR 225’s remote may be programmed to operate
so that the channel control function for either the TV,
cable or satellite receiver used in your system may be
used in conjunction with one of the other devices con-
trolled by the remote. For example, while using and con-
trolling the VCR, you may wish to change channels on a
cable box or satellite receiver without having to change
the device selected by the AVR 225 or the remote. To
program the remote for Channel Control Punch-
Through, follow these steps:
1. Press the Input Selector Button e for the device
you will be using (e.g.,VCR) when you wish to have
Channel Punch-Through active and the Mute
Button at the same time until the red light
appears under the Input Selector e and the
Program/SPL Indicator c flashes amber.
2. Press the Volume Down Button .The
Program/SPL Indicator c will stop flashing and
stay amber.
3. Press and release the Input Selector Button e
for the device that will be used to change the chan-
nels.The Program/SPL Indicator c will blink
green three times and then go out to confirm the
data entry.
Example: To control the channels using your cable
box or satellite receiver while the remote is set to
control the VCR, first press the VID1/VCR Input
Selector Button e and the Mute Button
at the same time. Next, release them and press the
Volume Down Button ,followed by the
VID2/TV Input Selector Button e.
NOTE: To remove the Channel Control Punch-Through
and return the remote to its original configuration, repeat
the steps shown above. However, press the same but-
ton in Steps 1 and 3.
Transport Control Punch-Through
The AVR 225’s remote may be programmed to operate
so that the Transport Control Functions x (Play,
Stop, Fast Forward, Rewind, Pause and Record) for a
VCR, cassette deck, DVD or CD will operate in conjunc-
tion with one of the other devices controlled by the
remote. For example, while using and controlling the TV,
you may wish to start or stop your VCR or DVD without
having to change the device selected by the AVR 225
or the remote.To program the remote for Transport
Control Punch-Through, follow these steps:
1. Press the Input Selector e for the device you will
be using (e.g.,TV) when you wish to have Transport
Control Punch-Through active and the Mute Button
at the same time until the red light appears
under the Input Selector e and the
Program/SPL Indicator c flashes amber.
2. Press the Play Button x.The Program/SPL
Indicator c will stop flashing and stay amber.
3. Press and release the Input Selector Button e
for the device whose transport mechanism will be
controlled (e.g., DVD, CD).The Program/SPL
Indicator c will blink green three times and then
go out to confirm the data entry.
Example: To control the transport of a DVD player
while the remote is set to control the TV, first press
the VID2/TV Input Selector Button e and the
Mute Button at the same time. Next, release
them and press the Play Button x,followed by
the DVD Input Selector Button e.
NOTE: To remove the Channel Control Punch-Through
and return the remote to its original configuration, repeat
the steps shown above. However, press the same but-
ton in Steps 1 and 3.
Resetting the Remote Memory
As you add components to your home theater system,
occasionally you may wish to totally reprogram the
remote control without the confusion of any commands,
macros or “Punch-Through” programming that you may
have done.To do this, it is possible to reset the remote
to the original factory defaults and command codes by
following these steps. Note, however, that once the
remote is reset, all commands or codes that you have
entered will be erased and will need to be reentered:
1. Press any of the Input Selector Buttons e and
the “O” Button r at the same time until the
Program/SPL Indicator c begins to flash amber.
2. Press the “3” Button r three times.
3.The red LED under the Input Selector e will go
out and the Program/SPL Indicator c will stop
flashing and turn green.
4.The Program/SPL Indicator c will remain green
until the remote is reset. Note that this may take a
while, depending on how many commands are in the
memory and need to be erased.
5.When the Program/SPL Indicator c goes out,
the remote has been reset to the factory settings.
38
38
34
38
34
38
34
38
34
38
38
34
34 PROGRAMMING THE REMOTE
PROGRAMMING THE REMOTE