Filter
Top Products
23
ENGLISH
INSTALLATION
STEP TWELVE – Plug in AC Power Cords
Before plugging the AVR into an unswitched electrical outlet, make sure
the Main Power Switch behind the front-panel door is off, to prevent the
possibility of damaging the AVR in case of a transient power surge. When
pressed in, the switch is on. When pressed again to unlatch it, the switch pops
out.
You may plug one device that draws no more than 50 watts into the AC
Switched Accessory Outlet on the rear panel. Turn on the device’s mechanical
or master power switch, and that device will power on any time the AVR 760/
AVR 660 is turned on (some devices may require additional steps to power
on from their standby mode). If the device has a clock or must always be on
(such as a cable set-top box programmed to make recordings), do not plug it
into this outlet.
The AVR 760/AVR 660 is equipped with a detachable power cord, allowing
you to fully wire your system before installing the AVR. Plug the male end of
the cord into an unswitched AC outlet, and the female end into the AVR 760/
AVR 660.
The Advanced Manual available for download from the harman/kardon web
site contains a Table A5 designed for you to enter the information from Table
2 for future reference.
STEP THIRTEEN – Insert Batteries in Remote
The AVR 760/AVR 660 remote control uses four AAA batteries (included).
To remove the battery cover located on the back of the remote, squeeze the
tab and lift the cover.
Insert the batteries as shown in Figure 18, observing the correct polarity.
Figure 18 – Remote Battery Compartment
Point the remote’s lens toward the front panel of the AVR 760/AVR 660.
Make sure no objects, such as furniture, are blocking the remote’s path to
the receiver. Bright lights, fluorescent lights and plasma video displays may
interfere with the remote’s functioning. The remote has a range of about 7
meter, depending on the lighting conditions. It may be used at an angle of up
to 30 degrees to either side of the AVR.
Leave the Zone Selector Switch at the bottom in the Zone 1 position for
normal use.
If the remote seems to operate intermittently, or if pressing a button on the
remote does not cause the AVR Settings Button or one of the Source Selectors
to light, check or replace the batteries.
STEP FOURTEEN – Program Sources Into the
Remote
The AVR 760/AVR 660 remote may be programmed to control many brands
and models of DVD players, cable boxes, satellite receivers, the Harman
Kardon DMC 1000 digital media center and TVs. It is also preprogrammed to
operate your iPod when docked in The Bridge II.
To access the functions for a particular device, switch the remote’s device
mode. Press the AVR Settings Button to access the codes that control the
receiver, or the Source Selector Buttons to access the codes for the devices
programmed into the remote.
To program the codes for a source device into the remote:
Turn on the source device.1.
Access the remote’s menu system by pressing and holding the AVR 2.
Settings Button for 3 seconds, until the “Main Menu” and “Program
Device” messages appear in the LCD Display.
Press the OK Button to select the Program Device function.3.
Use the 4.
KL
Buttons to select the Source Selector (or device) to program,
and press the OK Button when the desired device appears on the lower
line of the LCD Display.
For two of the Source Selectors and for sources A, B, C and D, the next step 5.
requires you to specify the device type. For the other Source Selectors,
proceed to step 6.
Cable/SAT
• : Use the
KL
Buttons to select either a cable television
or satellite television set-top box, and press the OK Button.
AUX
• : Use the
KL
Buttons to select a CD player, HDTV set-top box,
PVD (personal video device, such as a DVR), TiVo system or VCR. Press
the OK Button when the desired device appears.
A, B, C, D
• : Select any desired device type.
Select whether to program the device manually or use the remote’s Auto 6.
Search capability. Manual programming simply requires you to select the
brand name of your device and try a handful of possible codes. There is no
need to look up numeric codes; the AVR 760/AVR 660 does the work for
you. It is recommended that you select Manual programming first.
• Manual Programming
: Use the
KL
Buttons to scroll through the
list of brands for which the remote has codes stored in its library. When your
brand appears on the lower line, press the OK Button.
The remote will look up the brand in its library and display the number of
codes available. Press the “1” Alphanumeric Key first. The remote will transmit
the Power Off command associated with the first code set to the device. If
the device turns off, then a compatible code set has been found. Press the OK
Button to accept it.
If the device remains powered on, press the “2” Alphanumeric Key. Proceed
in this fashion until either a compatible code set is found, or you run out of
codes for that brand.
If you run out of codes, press the Back/Exit Button to end the process, and
repeat steps 2 through 5. At step 6, select Auto and follow the instructions in
the next bullet.