Filter
Top Products
14-EN
3
Press MENU to select RETURN.
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
• This function is inoperable when DEFEAT is set to ON (this page).
• EQ mode is automatically canceled if no buttons are pressed
within 15 seconds.
Adjusting and Storing the Equalizer Curve
You can modify the Equalizer settings to create a response curve more
appealing to your personal taste.
1
Press and hold MENU for at least 2 seconds.
2
Press MENU to select USER EQ (USER'S EQ for
CDA-9833).
3
Press BAND/TEL. to select your desired
frequency band.
BAND1 → BAND2 → BAND3 → BAND4 → BAND5 →BAND1
4
Press g or f to select your desired
frequency.
Adjustable frequency bands:
20Hz to 20kHz(in 1/3 octave steps)
5
Turn the Rotary encoder to adjust the level.
6
Press SOURCE/POWER to select your desired
band width (Q).
Adjustable band width: 1.0, 1.5, 3.0
To store the adjusted curve
1) Press and hold, for at least 2 seconds, any one of the
preset buttons (1 through 6) into which you wish to store
the adjusted curve.
7
To set another channel, repeat steps 3 to 6.
8
Press the Rotary encoder to confirm the
adjusted contents.
The adjusted contents are not stored if the Rotary encoder
is not pressed.
9
After setting, press MENU to select RETURN.
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
• The frequencies of adjacent bands cannot be adjusted within 4 steps.
• EQ mode is automatically canceled if no buttons are pressed
within 15 seconds.
• This function is inoperable when DEFEAT is set to ON (this page).
Indicators for sound setting
Sound Setting
Adjusting Balance (Between Left and Right)/
Fader (Between Front and Rear)/Defeat
1
Press Rotary encoder repeatedly to choose the
desired mode.
Each press changes the modes as follows:
SUBWOOFER*
1
→ BALANCE → FADER → DEFEAT →
VOLUME → SUBWOOFER*
1
Subwoofer : 0 ~ +15
Balance : L15 ~ R15
Fader : R15 ~ F15
Defeat : ON/OFF
Volume : 0 ~ 35
Press g or f after selecting the Subwoofer mode,
and the subwoofer output phase is toggled NORMAL
(PHASE 0°) or REVERS (PHASE 180°).
• If the Rotary encoder is not pressed within 5 seconds after
selecting the BALANCE, FADER, DEFEAT or SUBWOOFER
mode, the unit automatically returns to normal mode.
• If you set the 2WAY/3WAY switch (pages 40 to 42) to 3WAY, you
cannot adjust the FADER mode.
*
1
When the subwoofer mode is set to OFF, its level and phase cannot
be adjusted.
2
Turn the Rotary encoder until the desired sound
is obtained in each mode.
By setting Defeat ON, previously adjusted settings of EQ
will return to the factory defaults and MX is turned off.
• Depending on the connected devices, some functions and display
indications do not work.
Equalizer Presets
3 typical equalizer settings are preset at the factory for a variety of
musical source material.
1
Press MENU to select Factory's EQ.
2
Press either g or f.
With each press of the button, the equalizer mode will
display the selected equalizer characteristic.
FLAT(OFF) ↔ ROCK ↔ POPS ↔
NEWS ↔ USER'S 1 to 6
↔ FLAT(OFF)
FLAT (OFF) : Flat frequency
ROCK : Emphasize lows and highs
POPS : Emphasize midrange
NEWS : Boost midrange and suppress highs and lows
USER'S 1 to 6 : Recall the stored preset number in "Adjusting
and Storing the Equalizer Curve."
SOURCE/
POWER
g
f
BAND/
TEL.
Rotary encoder
Preset buttons (1 through 6)
MXMENU
Lights when MX is on.
Lights when the Equalizer, Crossover and Time Correction
(Bass Focus) are set to anything other than factory default.