Filter
Top Products
Additional Information
57
GB
FM tuner section
Tuning range 87.5 - 108.0 MHz
Antenna terminals 75 ohms, unbalanced
Intermediate frequency
10.7 MHz
Sensitivity
Mono: 18.3 dBf, 2.2 µV/75 ohms
Stereo:
38.3 dBf, 22.5 µV/75 ohms
Usable sensitivity 11.2 dBf, 1 µV/75 ohms
S/N
Mono: 76 dB
Stereo: 70 dB
Harmonic distortion at 1 kHz
Mono: 0.3%
Stereo: 0.5%
Separation 45 dB at 1 kHz
Frequency response 30 Hz – 15 kHz,
+0.5/–2 dB
Selectivity 60 dB at 400 kHz
AM tuner section
Tuning range
Models of area code U, CA
With 10-kHz tuning scale: 530 – 1710 kHz
5)
With 9-kHz tuning scale: 531 – 1710 kHz
5)
Models of area code E2/E3, AR, MX
With 10-kHz tuning scale: 530 – 1610 kHz
5)
With 9-kHz tuning scale: 531 – 1602 kHz
5)
Models of area code SP, CEL, CEK, TW, AU
With 9-kHz tuning scale: 531 – 1602 kHz
Antenna Loop antenna
Intermediate frequency
450 kHz
Usable sensitivity 50 dB/m (at 1,000 kHz or
999 kHz)
S/N 54 dB (at 50 mV/m)
Harmonic distortion 0.5 % (50 mV/m, 400 Hz)
Selectivity
At 9 kHz: 35 dB
At 10 kHz: 40 dB
5) You can change the AM tuning scale to 9 kHz or
10 kHz. After tuning in any AM station, turn off
the receiver. Hold down PRESET TUNING + and
press ?/1. All preset stations will be erased when
you change the tuning scale. To reset the scale to
10 kHz (or 9 kHz), repeat the procedure.
Video section
Inputs
Video: 1 Vp-p, 75 ohms
S-video: Y: 1 Vp-p, 75 ohms
C: 0.286 Vp-p, 75 ohms
Component Video: Y: 1 Vp-p, 75 ohms
P
B
B-Y: 0.7 Vp-p,
75 ohms
PR R-Y: 0.7 Vp-p,
75 ohms
Outputs
Video: 1 Vp-p, 75 ohms
S-video: Y: 1 Vp-p, 75 ohms
C: 0.286 Vp-p, 75 ohms
Component Video: Y: 1 Vp-p, 75 ohms
PB B-Y: 0.7 Vp-p,
75 ohms
P
R
R-Y: 0.7 Vp-p,
75 ohms
General
Power requirements
Area code Power requirements
U, CA, MX 120 V AC, 60 Hz
CEL, CEK 230 V AC, 50/60 Hz
SP, AR 220 – 230 V AC, 50/60 Hz
E2/E3 120/220/240 V AC, 50/60 Hz
TW 110 V AC, 50/60 Hz
AU 240 V AC, 50 Hz
Power consumption
Area code Power consumption
U, MX 210 W
CA 300 VA
CEL, CEK, AU, 180 W
E2/E3, SP, AR
TW 450 W
Power consumption (during standby mode)
0.5 W (when “A.PWR” in the SET UP menu is set to
“NO”) (page 38).
continued