Sony CMT-HPX10W Speaker System User Manual


 
masterpage:Left
filename[\\Nas-data-server\SONY Current jobs\SONY CMT-HPX10W-HPX9-
HPX7\DTP\4255291112\425529111CMTHPX10WCEL\GB12INF-CEL.fm]
30
GB
model name[CMT-HPX10W/CMT-HPX9/CMT-HPX7]
[4-255-291-11(2)]
On operating voltage
Before operating the system, check that the operating
voltage of your system is identical with the voltage of
your local power supply.
The voltage selector is located at the bottom of the
apparatus.
On safety
The unit is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the unit itself has been turned off.
Unplug the system from the wall outlet (mains) if it
is not to be used for an extended period of time. To
disconnect the power cord (mains lead), pull it out by
the plug. Never pull the cord itself.
Should any solid object or liquid fall into the system,
unplug the system and have it checked by qualified
personnel before operating it any further.
AC power cord must be changed only at the qualified
service shop.
On placement
Do not place the system in an inclined position.
Do not place the system in locations where it is;
Extremely hot or cold
Dusty or dirty
Very humid
Subject to vibrations
Subject to direct sunlight
Use caution when placing the unit or speakers on
surfaces that have been specially treated (with wax,
oil, polish, etc.) as staining or discoloration of the
surface may result.
On heat buildup
Although the system heats up during operation, this
is not a malfunction.
Place the system in a location with adequate
ventilation to prevent heat build-up in the system.
If you continuously use this system at a high volume,
the cabinet temperature of the top, side and bottom
rises considerably. To avoid burning yourself, do not
touch the cabinet.
To prevent a malfunction, do not cover the
ventilation hole.
On operation
If the system is brought directly from a cold to a
warm location, or is placed in a very damp room,
moisture may condense on the lens inside the CD
player. Should this occur, the system will not operate
properly. Remove the disc and leave the system
turned on for about an hour until the moisture
evaporates.
When you move the system, take out any disc.
If you have any questions or problems concerning your
system, please consult your nearest Sony dealer.
Notes on discs
Before playing, clean the disc with a cleaning cloth.
Wipe the disc from the center out.
Do not use solvents such as benzene, thinner,
commercially available cleaners or anti-static spray
intended for vinyl LPs.
Do not expose the disc to direct sunlight or heat
sources such as hot air ducts, nor leave it in a car
parked in direct sunlight.
Do not use discs encircled with a protection ring.
This may cause a malfunction to the system.
When using discs that have glue or similar tacky
substance on the label side of the disc or that used a
special ink when the label was printed, there is a
chance that the disc or label may become attached to
parts inside this unit. When this occurs, it may not be
possible to remove the disc, and may also cause this
unit to malfunction. Be sure to check that the label
side of the disc is not sticky before using.
The following types of disc should not be used:
Rental or used discs with attached seals where the
glue extends beyond the seal. The perimeter of the
seal on the disc is tacky.
Discs that have labels printed using a special ink
that feels tacky when touched.
Discs with non-standard shapes (e.g., heart, square,
star) cannot be played on this unit. Attempting to do
so may damage the unit. Do not use such discs.
Cleaning the cabinet
Clean the cabinet, panel and controls with a soft cloth
slightly moistened with mild detergent solution. Do not
use any type of abrasive pad, scouring powder or
solvent such as thinner, benzene or alcohol.
Additional Information
Precautions