Filter
Top Products
38
GB
Changing the recorded level after recording
Editing Recorded MDs
Changing the recorded
level after recording
(S.F EDIT)
You can change the volume of recorded tracks using S.F
(Scale Factor) Edit. The original track is recorded over at
the new recording level. When changing the recording
level, you can select Fade-in Recording to gradually
increase the signal level at the start of recording, or Fade-
out Recording to gradually decrease the signal level at the
end of recording.
1
Press S.F EDIT.
“S.F Edit” appears in the display.
2
Turn AMS (or press ./> repeatedly) until “Tr
Level ?” appears, then press AMS or YES.
3
Turn AMS (or press ./> repeatedly) until the
track number you want to change the recording
level appears, then press AMS or YES.
“Level 0dB” appears in the display.
4
While monitoring the sound, turn AMS (or press
./> repeatedly) to change the recorded level
without turning on the two rightmost indicators on
the peak level meters.
You can set the level at any value between –12 dB and
+12 dB, in 2 dB increments.
5
Press AMS or YES.
“Edit OK?” appears in the display.
6
Press AMS or YES.
The deck starts recording over the existing track. “S.F
Edit: ** %” appears while the track is being recorded.
An amount of time that is roughly equal to or longer
than the playback time of the track is required when
recording over the track. When the recording finishes,
“Complete!!” appears in the display for a few seconds.
1
Press S.F EDIT.
“S.F Edit” appears in the display.
2
Turn AMS (or press ./> repeatedly) until
“Fade In ?” or “Fade Out ?” appears, then press
AMS or YES.
3
Turn AMS (or press ./> repeatedly) until the
track number you want to change the recording
level appears, then press AMS or YES.
“Time 5.0s” appears in the display.
4
While monitoring the sound, turn AMS (or press
./> repeatedly) to change the Fade-in or
Fade-out Recording time.
The deck plays the portion that will be recorded over
using Fade-in or Fade-out Recording.
You can set the time at any value between 1 second
and 15 seconds, in 0.1 second increments. You cannot
set the time longer than the track.
5
Press AMS or YES.
“Edit OK?” appears in the display.
6
Press AMS or YES.
The deck starts recording over the existing track. “S.F
Edit: ** %” appears while the track is being recorded.
When the recording finishes, “Complete!!” appears in
the display for a few seconds.
To cancel the operation
Press MENU/NO or
x
in steps 1 to 5. If you press AMS
or YES in step 6 and recording starts, you cannot interrupt
the operation.
z
You can use Edit Menu to perform S.F Edit
1
While the deck is stopped, press MENU/NO.
“Edit Menu” appears in the display.
2
Turn AMS (or press
.
/
>
repeatedly) until “S.F Edit?”
appears, then press AMS or YES.
3
Turn AMS (or press
.
/
>
repeatedly) until “Tr Level ?,”
“Fade In ?,” or “Fade Out ?” appears, then press AMS or YES.
4
Turn AMS (or press
.
/
>
repeatedly) to adjust the
recording level or Fade-in or Fade-out Recording time.
5
Press AMS or YES.
Notes
• Do not disconnect the AC power cord or move the deck
while recording is in progress. This may damage the
recording data preventing recording from being performed
properly.
•
You cannot change the recorded level of a track recorded in
LP2 or LP4 Stereo mode.
•
Do not use an MD that is damaged or dirty. This may prevent
recording data from being recorded properly.
•
Repeatedly changing the recording level results in poor sound
quality.
•
The recording level will not return to the exact original level
once the recording level has been changed even if it returned to
the original level.
•
The recording level cannot be changed while the timer is
activated.
Changing the overall recording level
AMS YES
S.F EDIT
Avoid turning on these indicators
Fade-in and Fade-out Recording