Filter
Top Products
15
EN
Writing Sub Codes
3-856-761-11(2)
Manual Writing of Start IDs During
Recording
Press WRITE.
“ID WRITE” appears in the display for a few seconds
and the start ID is written on the tape at the selected
position. “START ID” flashes in the display during this
time.
ID WRI TE
START ID
Start ID
Note
The interval between start IDs must be more than 18 seconds
(36 seconds in long-play mode). If the interval is less than 18
seconds (or 36 seconds), the deck may fail to detect the
second start ID during playback.
Writing the Start IDs Automatically During
Recording
Do the following procedure to automatically write
program numbers along with start IDs at the same
position.
• When recording an analog signal with the INPUT
switch at ANALOG
A start ID and program number are written whenever the
input signal rises above a given level after remaining at a
muted or low level for 3 seconds or more.
• When recording a digital signal with the INPUT
switch at OPTICAL or COAXIAL
A start ID and program number are written whenever a
new track is detected while recording a digital signal
through the COAXIAL IN or OPTICAL IN jack from a
digital source such as CD player or another DAT deck.
Start IDs and program numbers are not written, however,
for tracks that are less than 18 seconds in length.
1 Do Steps 1 to 7 of “Recording on a DAT” on pages
6 and 7.
The deck changes to recording pause.
2 Press START ID AUTO repeatedly until “AUTO”
appears in the display.
3 If you are recording from the end of the recorded
portion, use the number buttons to specify the
program number after the last one recorded.
Example: When program number 5 is the last
program number recorded on the tape.
The next program
number
PGM NO.
AUTO
REC
·
∏
6
If the last program number on the tape appears in
the display, you don’t have to specify the next
program number. If you are recording from the
beginning of a blank tape, program number “1”
appears in the display. If you forget program
numbering at this time, you can add them later
(see “Renumbering the Program Numbers
Automatically (Renumbering)” on page 17).
4 To start recording, press PAUSE P or PLAY (,
then start playing the program source.
Start IDs are written on the tape automatically
during recording.
“ID WRITE” appears for a few seconds whenever
a sub codes (a start ID and program number) are
being written.
During digital recording from a CD player
Start recording on your deck first, then press the (
PLAY button on the CD player while it is stopped. If
you place your deck into recording pause and the CD
into play pause before you start recording, the start ID
and program number of the first track on the CD may
not be correctly written to the tape.
Note
During automatic start ID writing the positioning of some
start IDs may be inaccurately or inappropriately positioned
away from the beginning of the track. If this happens, you
can reposition or erase the start IDs later (see “Accurate
Positioning of Start IDs (Rehearsal)” and “Erasing Start IDs”
on page 16).
Writing Start IDs During
Playback
You can write start IDs during playback.
REW 0 / FF )
WRITE
START ID REHEARSAL
MARGIN
OPEN/CLOSE
RESET
RESETMODE
REWPREVIOUS FFNEXT
AMS
TIMER
START ID
PHONESSBMINPUT REC MODE
RECREC MUTEPAUSEPLAYSTOP
PHONE LEVEL
REC LEVEL
RENUMBER REHEARSALAUTO
WRITE ERASE
g
§
5
46
0
37
28
19
10
100
ON
48kHz
44.1kHz
LONG
ANALOG
OPTICAL
COAXIAL
STANDARD
OFF
RECOFF
POWER
PLAY
=
pP
Rr
(
+ 0)
L R
Press WRITE.
“ID WRITE” appears in the display for a few seconds
and the start ID is written on the tape at the selected
position. “START ID” flashes in the display during
this time.