Filter
Top Products
13
EN
Playback Operations
3-856-761-11(2)
Playing Tracks Repeatedly
(Repeat Play) Z
You can play a specific track or all the tracks on the
tape repeatedly.
OPEN/
CLOSE MODE
123
456
789
0
COUNTER
RESET
REPEATCLEAR
6
REPEAT
Playing all tracks repeatedly
Press REPEAT repeatedly while playing a track until
“REPEAT” appears in the display. The deck will then
play back all tracks until it detects the end of the last
track, which may be:
— a blank section of 9 seconds or more
— the end of the tape
When the deck detects either of the above, it rewinds
the tape to beginning and plays back all tracks again.
The deck repeats this cycle up to 5 times, then
automatically stops.
To stop playing all tracks repeatedly
Press REPEAT repeatedly until “REPEAT” disappears.
Note
Repeat Play of all tracks is canceled when you take out the
cassette.
Playing a track repeatedly
Press REPEAT repeatedly while playing the track that
you want until “REPEAT 1” appears in the display.
The deck will then play back the track until its end,
which may be:
—the next start ID
—a blank section of 9 seconds or more
—the end of the tape
When the deck detects any of the above, it rewinds the
tape and starts playing from the start ID of the same
track again. The deck repeats this cycle up to 5 times,
then automatically stops.
To stop playing a track repeatedly
Press REPEAT repeatedly until “REPEAT 1” disappears.
Note
Repeat Play of a single track is canceled when you take out
the cassette.
If “EMPHASIS” appears in the display
The deck is playing an audio signal recorded with
emphasis (in the higher frequencies). The deck,
however, plays the signal while automatically
deemphasizing it (with attenuation proportional to the
degree of emphasis).
Locating a Track (AMS*/Direct
Access)
You can locate the tracks in a number of ways, but only
after you have recorded start IDs on the tape (see pages
14 to 16). To use Direct Access, program numbers
must be recorded on the tape (see pages 14 and 17).
The beginning of the next
or succeeding tracks
(AMS)
NEXT + as many times as you
want while playing. For example,
to locate the second track ahead,
press twice.
PREVIOUS = once while
playing
The beginning of the
current track(AMS)
The beginning of
preceding tracks (AMS)
PREVIOUS = as many times as
you want while playing. For
example, to locate the second track
behind, press three times.
By specifying the program
number of a track
(Direct Access)
Z
1 Enter the program number of
the track with the number buttons.
2 Press (.
To locate Press
PREVIOUS = / NEXT +
PLAY (
MARGIN
OPEN/CLOSE
RESET
RESETMODE
REWPREVIOUS FFNEXT
AMS
TIMER
START ID
PHONESSBMINPUT REC MODE
RECREC MUTEPAUSEPLAYSTOP
PHONE LEVEL
REC LEVEL
RENUMBER REHEARSALAUTO
WRITE ERASE
g
§
5
46
0
37
28
19
10
100
ON
48kHz
44.1kHz
LONG
ANALOG
OPTICAL
COAXIAL
STANDARD
OFF
RECOFF
POWER
PLAY
=
pP
Rr
(
+ 0)
L R
* AMS = Automatic Music Sensor.
z If you enter the wrong program number during
Direct Access
Z
If you haven’t pressed the ( button, press the CLEAR
button on the remote, then enter the correct number. If
you have already pressed the ( button, pressing the
CLEAR button will not erase the wrong program
number. Stop the deck and reenter the program
number.
z If the deck detects a blank section of 9 seconds or
more, or the end of the tape
The deck rewinds the tape automatically to its
beginning and stops (Auto Rewind).
z You can make the deck start playing automatically
from the beginning of the tape after rewinding
Press PLAY ( while holding down REW 0.