Filter
Top Products
11
EN
Recording Operations
3-856-761-11(2)
Inserting a Sound-Muted
Section While Recording
(Record Muting)
Use Record Muting to insert a space of about 4 seconds
between tracks. This is recommended if you plan to
copy the DAT tape to an analog audio cassette tape
since the spaces will allow you to use automatic search
functions to locate the beginning of each track.
When you start recording from the beginning of a
blank tape and want to insert a space before the first
track, be sure to create a sound-muted section using
Record Muting only. Do not advance the tape with the
FF ) or PLAY ( button since this will create a
blank section on the tape (see page 9).
z The counter in long-play mode
The displayed tape running time, absolute time and
remaining time on the tape are for standard-play mode.
Double the time to obtain the corresponding times for
long-play mode.
Note
Do not change the INPUT or REC MODE setting while
recording. This may cause an error in the “PGM TIME”
(playing time of the track) display.
Using the SBM (Super Bit
Mapping) Function
You can use the SBM function to record on analog
input signal only when the INPUT switch is set to
ANALOG and the REC MODE switch to STANDARD
(either 48 kHz or 44.1 kHz). For details on the SBM
function, see “SBM (Super Bit Mapping) Function” on
page 20.
REC MUTE R
PLAY ( PAUSE P
MARGIN
OPEN/CLOSE
RESET
RESETMODE
REWPREVIOUS FFNEXT
AMS
TIMER
START ID
PHONESSBMINPUT REC MODE
RECREC MUTEPAUSEPLAYSTOP
PHONE LEVEL
REC LEVEL
RENUMBER REHEARSALAUTO
WRITE ERASE
g
§
5
46
0
37
28
19
10
100
ON
48kHz
44.1kHz
LONG
ANALOG
OPTICAL
COAXIAL
STANDARD
OFF
RECOFF
POWER
PLAY
=
pP
Rr
(
+ 0)
L R
1 Press REC MUTE R where you want to insert a
space while the deck is recording or in recording
pause.
The deck creates a sound-muted section as “REC”
flashes in the display.
After the sound-muted section is completed,
“REC” lights up and the deck changes to recording
pause.
To insert a blank space longer than 4 seconds
Hold down the REC MUTE R button as long as you
want. When you release the button, the sound-muted
section ends and the deck changes to become recording
pause. If you keep the button pressed longer than 4
seconds, “REC” will begin to flash more quickly and the
time elapsed after pressing the REC MUTE R button is
shown in the display.
When you release the REC MUTE R button, P in the
display stays on and the deck changes to recording
pause.
2 Press PAUSE P or PLAY ( to resume recording.
The deck starts recording again.
Note
If you do not create a sound-muted section at the beginning
of a tape, you may not be able to move or erase a start ID
(see page 14) that is recorded within 2 seconds from the
beginning of the tape.
Set SBM to ON.
“SBM” appears in the display during recording using
the SBM function.
To turn the SBM function off
Set SBM to OFF.
SBM
MARGIN
OPEN/CLOSE
RESET
RESETMODE
REWPREVIOUS FFNEXT
AMS
TIMER
START ID
PHONESSBMINPUT REC MODE
RECREC MUTEPAUSEPLAYSTOP
PHONE LEVEL
REC LEVEL
RENUMBER REHEARSALAUTO
WRITE ERASE
g
§
5
46
0
37
28
19
10
100
ON
48kHz
44.1kHz
LONG
ANALOG
OPTICAL
COAXIAL
STANDARD
OFF
RECOFF
POWER
PLAY
=
pP
Rr
(
+ 0)
L R