Filter
Top Products
E-13
Timer and sleep operation (Remote
control only) (continued)
To use timer and sleep operation together Q
Sleep and timer playback:
For example, you can fall asleep listening to the radio and
wake up to CD in the next morning.
Set the sleep time (see above, steps 1 - 5).
1
While the sleep timer is set, set the timer playback 2
(steps 2 - 10, page 12).
Sleep timer
setting
Timer playback
setting
End time
Timer playback
start time
Sleep operation will
automatically stop
Desired time1 - 90 minutes
Enhancing your system
The connection cord is not included. Purchase a
commercially available cord as shown below.
1
2
3
4
5
4
5
3
2
1
MINI COMPONENT SYSTEM
OPEN / CLOSE
TUNING
PRESET
USB
AUDIO IN
AUDIO IN
USB
PHONES
TAPE
TUNER
CD
TIMER
iPod/iPhone
POWER
ON/ STAND-BY
(BAND)
VOL.
VOL.
REMOTE
SENSOR
CD-DHS1050P
AUDIO IN
PHONES
Portable audio
player, etc.
Audio cable (not supplied)
To the
line
output
jack
Listening to the playback sounds of Q
portable audio player, etc.
Connect a portable audio player etc. to the front AUDIO 1
IN jack.
Press the ON/STAND-BY button to turn the power on.
2
Press the AUDIO IN/USB button repeatedly to select 3
AUDIO IN.
Play the connected equipment.
4
If volume level of the connected device is too high,
sound distortion may occur. Should this happen, lower
the volume of the connected device.
If volume level is too low, increase the volume of the
connected device.
Note:
To prevent noise interference, place the unit away from the
television.
Headphones Q
Before plugging in or unplugging the headphones, O
reduce the volume.
Be sure your headphones have a 1/8" (3.5 mm) diameter O
plug and impedance between 16 and 50 ohms. The
recommended impedance is 32 ohms.
Plugging in the headphones disconnects the speakers O
automatically. Adjust the volume using the VOLUME
control.
Troubleshooting chart
Many potential problems can be resolved by the owner
without calling a service technician. If something is wrong
with this product, check the following before calling your
authorized SHARP dealer or service center.
General Q
Symptom Possible cause
The clock is not set O
to the correct time.
Did a power failure occur? O
Reset the clock. (Refer page
11)
When a button is O
pressed, the unit
does not respond.
Set the unit to the power O
stand-by mode and then turn
it back on.
If the unit still malfunctions, O
reset it. (Refer page 14)
No sound is heard. O Is the volume level set to “0”? O
Are the headphones O
connected?
Are the speaker wires O
disconnected?
CD player Q
Symptom Possible cause
Playback does not O
start.
Playback stops in O
the middle or is not
performed properly.
Is the disc loaded upside O
down?
Does the disc satisfy the O
standards?
Is the disc distorted or O
scratched?
Playback sounds O
are skipped, or
stopped in the
middle of a track.
Is the unit located near O
excessive vibrations?
Is the disc very dirty? O
Has condensation formed O
inside the unit?
“ER-CD21” O
appears on the
display.
Is the disc tray stopped with O
force? Set the unit to the
power stand-by mode and
then turn it back on.
Cassette deck Q
Symptom Possible cause
Sound skipping. O
Cannot hear treble. O
Sound fl uctuation. O
Is there any slack? O
Is the tape stretched? O
Are the capstans, pinch O
rollers, or heads dirty?
Cannot remove the O
tape.
If a power failure occurs O
during playback, the heads
remain engaged with the
tape. Do not open the
compartment with great
force.
CD-DHS1050P_US_EN.indd 13CD-DHS1050P_US_EN.indd 13 2/10/2011 3:32:24 PM2/10/2011 3:32:24 PM