Filter
Top Products
7
Front Panel Display
The large fluorescent display in the center
portion of the RT-02 provides status informa-
tion used in operating the AM/FM receiver
(such as station frequency display, band, preset
memory, RDS information, etc.).
DIMMER Button
Available only on the remote control, this button
selects three display brightness settings:
NORMAL, DIM, or OFF. When the display is
OFF, pressing any button or control will re-
turn it to the NORMAL mode. Press the but-
ton to cycle through the three settings.
NOTE: When the tuner is turned off and back
on, the display reverts to its normal setting.
MEMORY Button
The MEMORY button is used to confirm and
memorize various settings in the setup and
operation of the RT-02, including tuner sta-
tion presets. Its use is described in detail in
the relevant sections below.
Setting Country Mode
The RT-02 has two default modes, one for the
USA and one for Europe. These configure the
unit for differences in local markets, includ-
ing FM tuning intervals, AM tuning intervals,
and differences in the European RDS and
United States RBDS standards. Your unit has
been factory configured to the correct default
mode for the country in which it was purchased.
To switch to the USA default mode,
press and hold the POWER, MEMORY, and
9 buttons for 5 seconds. The word LOADING
will appear in the DISPLAY and the unit will
power up in the USA configuration.
To switch to the European default
mode, press and hold the POWER, MEMORY,
and 0 buttons for more than 5 seconds. The
word LOADING will appear in the DISPLAY
and the unit will power up in the European
configuration.
Basic Tuning Controls
The RT-02 features a digital synthesized AM/
FM tuner with RDS or RBDS capability and 30
station presets. The unit offers a wide range
of tuning options. Here is an overview of the
tuning options (more detailed information is
provided in subsequent sections of this manual):
• Manual frequency tuning lets you
tune up or down to the next station fre-
quency. Set the TUNE/PRESET mode to
TUNE. Turn off AUTO TUNING. Use the
TUNING controls to tune up or down.
• Direct frequency tuning lets you en-
ter the desired station frequency digits. Press
the FREQUENCY DIRECT button on the re-
mote and enter the digits using the NU-
MERIC buttons.
• Automatic frequency search tun-
ing lets you search up or down to find the
next receivable broadcast signal. Set the
TUNE/ PRESET mode to TUNE. Turn on
AUTO TUNING. Use the TUNING controls
to search up or down.
• Memory station preset tuning lets
you directly enter the number of a memo-
rized station preset number. Enter the num-
ber of the memorized preset using the NU-
MERIC buttons.
• Preset scan tuning lets you scan up/
down through the memorized station pre-
sets. Press the PRESET SCAN button to begin
scanning.
• RDS (Europe) or RBDS (USA) tun-
ing provides a range of special tuning and
search features based on data codes en-
coded with the broadcast signal. See the
RDS section of this manual for detailed
information.
NOTE: Three buttons on the remote (ANT
A/B, FM IF NARROW, and ANN ATT) are
not used with the RT-02 tuner.
BAND Button
The BAND button selects whether the tuner will
receive AM or FM broadcast signals. Press the
button to toggle back and forth between AM
and FM. A corresponding indicator will light
at the left portion of the front panel DISPLAY
to confirm your choice. The currently tuned
station frequency will be shown.
TUNING Controls
A pair of buttons, labeled < TUNING > on
the front panel and < TUN/PRESET > on the
remote, serve as the main tuning controls for
the RT-02. You can use either the front panel
or remote buttons; their function is identical.
These controls provides different tuning func-
tions, depending on the mode of operation:
In the FREQUENCY TUNING mode
with AUTO TUNING off, press a TUN-
ING button to manually jump to the next fre-
quency, regardless of whether or not a sta-
tion is broad-casting on that frequency. [See
the TUNE/PRE-SET button and AUTO TUN-
ING button sections for details on changing
the tuning modes.]
In the FREQUENCY TUNING mode
with AUTO TUNING on, press a TUN-
ING button to start auto tuning. The tuner
begins automatically scanning up or down
through the frequencies until the next receiv-
able signal is detected. If this is not the de-
sired station, repeat the automatic tuning pro-
cedure to find the next station. Weak stations
will be skipped during auto tuning. If no re-
ceivable signal is detected, the tuner will re-
vert to the last previously tuned station. [See
the TUNE/PRESET button and AUTO TUNING
button sections for details on changing the
tuning modes.]
In the PRESET TUNING mode, press a
TUNING button to advance to the next memo-
rized station preset. [See the TUNE/PRESET
button section for details on changing the tuning
modes.]
In the RDS PTY search mode, press a
TUNING button to select the desired program
type from the scrolling list in the display. See
the section on RDS tuning for more details. [See
the RDS PTY button section for details.]
NOTE: Several indicators in the front panel
display assist tuning. A large display shows
the tuned frequency and increases or de-
creases during tuning. A signal strength indi-
cator shows the strength of the incoming
signal. A TUNED indicator lights when a suf-
ficiently strong signal is received. A ST indi-
cator lights when a stereo FM signal is
received. In addition, indicators show the
currently selected tuning mode.
English