Filter
Top Products
21
English
OTHER OPTIONS Menu
OTHER OPTIONS
RECORD: CD
DYNAMIC: Max
5.1CH: Off
POWER: Direct
RESET: Setup
ZONE2: Setup
ENT KEY=MAIN MENU UP KEY=up
+/– KEY=change DWN KEY=down
This menu, accessed from the MAIN menu,
provides access to a several miscellaneous
settings as follows:
RECORD: Select a signal for the record out-
puts by choosing one of the input sources.
DYNAMIC: steps through the three dynamic
range settings available in digital modes:
• MAX (no compression/full dynamic range)
• MID (moderate compression)
• MIN (full compression/minimum dynamic
range).
5.1CH: determines whether or 5.1 channel
input is turned ON or OFF.
POWER: This setting determines how the
RSP-976 powers up. With the default DIRECT
setting, the unit is fully activated when AC power
is applied; however, it may be put in STANDBY
mode using the front panel STANDBY or re-
mote POWER button. With the STANDBY set-
ting, the unit powers up in standby mode when
AC is applied and must be activated from the
front-panel or remote control. In ALWAYS-ON
mode, the unit remains fully active whenever
AC is present; the front panel and remote
STANDBY or POWER buttons are disabled.
RESET: Place the highlight on this line and press
the ENTER button to call a submenu (described
in the next section) to reset all settings to their
factory defaults.
ZONE 2: Place the highlight on this line and
press the ENTER button to call the ZONE 2
MENU for configuring Zone 2 operation.
Change settings on the OTHER OPTIONS menu
by highlighting the desired line using the UP/
DOWN buttons and using the +/– buttons to
step through the available settings. To return
to the MAIN menu, press the ENTER button.
Press the MENU key on the remote to cancel
the display and return to normal operation.
RESET Menu
Reset to factory
default settings:
YES = ENT KEY
NO = DWN KEY
The FACTORY DEFAULT menu resets all sys-
tem configuration settings to the factory sup-
plied settings. This menu is reached by high-
lighting the RESET line on the OTHER OPTIONS
menu and pressing ENTER.
Press the ENTER button to reset all settings. Press
the DOWN button to cancel this menu and
return to the OTHER OPTIONS menu without
restoring the default settings.
NOTE
: Resetting to factory default settings will
erase all stored settings including delay set-
tings, speaker settings, balance settings, in-
put settings and more. You will lose ALL system
configuration settings. Be certain that you wish
to do so before resetting the factory defaults.
ZONE 2 SETUP Menu
ZONE2 SETUP
SOURCE: CD
VOLUME SETUP: Variable
VOLUME: 20
ENT KEY=MAIN MENU UP KEY=up
+/– KEY=change DWN KEY=down
The ZONE 2 SETUP menu provides settings
and configuration options related to the op-
eration of Zone 2. This menu is reached by
highlighting the ZONE 2 line on the OTHER
OPTIONS menu and pressing ENTER.
SOURCE: the source selected for listening in
Zone 2. Selecting the OFF option turns Zone
2 off.
VOLUME SETUP: configures the Zone 2
outputs for VARIABLE or FIXED volume levels.
VARIABLE allows control of the volume settings
in Zone 2 from the RSP-976 front panel or from
a remote control and IR repeater in Zone 2.
FIXED output disables the Zone 2 volume
control. In this mode, the Zone 2 level can be
fixed at the level specified on the next line,
thus optimizing system performance when send-
ing a fixed level signal to a preamp or ampli-
fier with its own volume adjustment.
VOLUME: In VARIABLE output mode, this line
shows the current volume setting for Zone 2.
In FIXED output mode, this use this setting to
establish a permanent fixed output level for
Zone 2.
Move the highlight to the desired line using
the UP/DOWN buttons and use the +/– but-
tons to adjust the volume level. To return to the
MAIN menu, press the ENTER button. Press
the MENU key on the remote to cancel the
display and return to normal operation.