Filter
Top Products
9
English
To select track numbers greater than 10 use the >10 button. For
example, to select track 14, press the >10 button followed by the 4
button. To select track 23, press the >10 button twice followed by the
3 button. The number of the selected track will appear in the main
numeric area at the center of the Display.
The DIRECT ACCESS buttons may also be used to memorize tracks in
PROGRAM mode (see PROGRAM Button section).
SEARCH Buttons
7K
The
]
and
[
buttons fast forward or fast reverse through the disc
that is playing. One press of the
]
or
[
button will fast forward
or fast reverse at 2X normal speed. Pressing the
]
or
[
button
repeatedly will fast forward or fast reverse at 4X, then 8X, 16X
and 32X normal speed. One more press of the
]
or
[
button, or
pressing the Play
/
button, returns the RCD-1520 to normal speed
play. While the buttons are pressed, you will hear high-speed audio.
EJECT Button
6N
When a disc is inserted into the front panel Disc Slot
=
it is pulled
into the disc transport. To eject the disc press the EJECT button on the
front panel
6
or the remote control
N
.
If you accidentally press either of these buttons, press the button again
to re-load the disc.
Additional Features
These convenience features add extra functionality to the RCD-1520,
including the ability to memorize a group of tracks to be played, to
repeat a disc, a program, or a track over and over, to play the tracks
on a disc in random order, to automatically play the first 10 seconds
of each track, and to select from several available time displays.
PROGRAM Button
2J
This button, labeled PROG, allows you to memorize more than
20 tracks on the current disc for playback in a specific order. For
example, you could instruct the RCD-1520 to play track 5, followed by
track 3, followed by track 8.
Note: Programmed play lists cannot be set up with MP3 and WMA
discs.
To begin a program:
1. Insert a disc in the front panel slot. The RCD-1520 will read the
contents of the disc. You may press the PLAY
/
button if you would
like to listen to the tracks while you program them.
2. Press the PROGRAM button on the front panel or the remote
control. The PROGRAM indicator will light up in the Display,
along with “P:00” indicating that the unit is waiting for the first
track to be memorized.
Transport Control Buttons
These buttons provide basic control functions for the disc transport
mechanism. Except where noted, all functions are available on the
RCD-1520 front panel and the IR remote control.
PLAY Button
qE
After the disc is loaded, press the PLAY
/
button to start playing the
disc. The number of the track being played and the elapsed time will
be shown in the display, along with the PLAY indicator. Normally, the
disc will start playing with the first track. However, you can select a
different track using the TRACK buttons or the DIRECT ACCESS buttons
(see below) before pressing the PLAY button to start playing a different
selection.
STOP Button
wD
Press the STOP
.
button once to stop disc play. Press the PLAY
/
button to resume disc play where it was stopped. If the STOP
.
button is press twice, disc play stops, the display shows STOP and
programmed selections are deleted (see below). When the PLAY
/
button is press after pressing the STOP
.
button twice, the disc begins
playing from the first track.
PAUSE Button
eL
The PAUSE
,
button is used to temporarily suspend play. The disc
continues to spin and play will be resumed from the current position.
The PAUSE indicator will light in the Display. To resume playing the
disc, press the PLAY button.
TRACK Buttons
rtM
These buttons are used to select tracks on the disc. When a disc is
playing, pressing the
}
TRACK button advances to the beginning of
the next track. Pressing the
{
TRACK button returns to the beginning
of the current track. Pressing
{
TRACK twice quickly in succession
returns to the beginning of the previous track. The new track number
appears in the Display.
These buttons are also used to select a track before pressing the PLAY
button or when memorizing tracks for the PROGRAM play mode (see
below). These selections are made by continuously pressing the TRACK
buttons until the desired track is reached.
In PROGRAM mode, the TRACK buttons advance or reverse to the next
track in the memorized selection list.
DIRECT ACCESS Buttons
F
(remote only)
These eleven numeric buttons (labeled 1 through 0 and >10) are used
to directly access a track from the IR remote control instead of stepping
through the tracks using the TRACK buttons.
The first ten tracks on a disc can be selected by pressing the
corresponding button. For example, to play the third track, press the 3
button on the remote control. To play track 10 press the 0 button.