Filter
Top Products
Controls and displays
1
1
10
4
62
7
10
Number buttons and other component controls
Use the number buttons to directly select a radio frequency
(page 33
) or the tracks on a CD, etc. There are other buttons
that can be accessed after is pressed. (For example
MIDNIGHT
, etc.)
EQ
– Press to switch on/off Acoustic Calibration EQ
setting (page 36
).
PHASE
– Press to switch on/off Phase Control (page 36).
SIGNAL SEL
– Press to select the audio input signal of the
component to play back (page 25
).
S.RETRIEVER
– Press to restore CD quality sound to
compressed audio sources (page 35
).
SB CH
(VSX-1023 only) – Press to select ON, AUTO or OFF
the surround back channel (page 36
).
CH SELECT
– Press repeatedly to select a channel, then
use
LEV +/–
to adjust the level (page 50).
LEV +/–
– Use to adjust the channel level.
MIDNIGHT
– Switches to Midnight or Loudness listening
(page 37
).
SPEAKERS
– See Switching the speaker terminal on
page 15.
DIMMER
– Dims or brightens the display. The brightness
can be controlled in four steps.
During ECO mode, the brightness switches between 2
levels. If the dimmest level is selected, DIMMER will be
shown on the display. (Mode other than ECO: 4 levels, ECO
mode: 2 levels)
+Favorite
– Press while a song is being played back or
stopped. The selected song is then registered in the
Favorites folder (page 42
).
11
SOURCE
Press to turn on/off other components connected to the
receiver (page 57
).
12
TV CONTROL buttons
These buttons are dedicated to control the TV assigned to the
TV
button. Thus if you only have one TV to hook up to this
system assign it to the
TV
button (page 58).
– Use to turn on/off the power of the TV.
INPUT
– Use to select the TV input signal.
CH +/–
– Use to select channels.
VOL +/–
– Use to adjust the volume on your TV.
13
ECO
Switches between ECO Mode 1/ECO Mode 2. When ECO
Mode is turned ON, the display will go dark (page 35
).
14
VOLUME +/–
Use to set the listening volume.
15
MUTE
Mutes/unmutes the sound.
16
DISP
Switches the display of this unit. The listening mode, sound
volume, Speaker System (VSX-1023) setting or input name can
be checked by selecting an input source.
•
The Speaker System setting may or may not be displayed,
depending on the input source you have selected.
Loading the batteries
The batteries included with the unit are to check initial
operations; they may not last over a long period. We
recommend using alkaline batteries that have a longer life.
CAUTION
•
Incorrect use of batteries may result in such hazards as
leakage and bursting. Observe the following precautions:
-
Never use new and old batteries together.
-
Insert the plus and minus sides of the batteries properly
according to the marks in the battery case.
-
Batteries with the same shape may have different
voltages. Do not use different batteries together.
-
When disposing of used batteries, please comply with
governmental regulations or environmental public
institution’s rules that apply in your country/area.
-
Do not use or store batteries in direct sunlight or other
excessively hot place, such as inside a car or near a
heater. This can cause batteries to leak, overheat,
explode or catch fire. It can also reduce the life or
performance of batteries.
-
When inserting the batteries, make sure not to damage
the springs on the battery’s (–) terminals. This can cause
batteries to leak or overheat.
Operating range of remote control
The remote control may not work properly if:
•
There are obstacles between the remote control and the
receiver’s remote sensor.
•
Direct sunlight or fluorescent light is shining onto the
remote sensor.
•
The receiver is located near a device that is emitting
infrared rays.
•
The receiver is operated simultaneously with another
infrared remote control unit.
RECEIVER
30°
7 m (23 ft.)
30°
VSX-1023_823_UCSMXCN_En.book 10 ページ ２０１２年１２月１８日 火曜日 午前１１時７分