Filter
Top Products
Controls and displays
04
25
En
7 TV CONTROL buttons
These buttons are dedicated to control the TV assigned to
the
TV CTRL
button. Thus if you only have one TV to hook
up to this system assign it to the
TV CTRL
input source
button. If you have two TVs, assign the main TV to the
TV
CTRL
button (see page 54 for more on this).
TV
– Use to turn on/off the power of the TV.
TV VOL +/–
– Use to adjust the volume on your TV.
INPUT SELECT
– Use to select the TV input signal.
TV CH +/–
– Use to select channels.
8 Component control buttons
The main buttons (
,
, etc.) are used to control a
component after you have selected it using the input
source buttons.
The controls above these buttons can be accessed after
you have selected the corresponding input source button
(for example
DVD
,
DVR1
or
TV
). The following controls
can be accessed when listening to the built-in tuner:
MPX
– Switches between stereo and mono reception
of FM broadcasts. If the signal is weak then switching
to mono will improve the sound quality (page 33).
DISP
– Switches between named station presets and
radio frequencies (page 34). Also used to display
RDS information (page 34).
EON
– Use to search for programs that are
broadcasting traffic or news information (page 35).
9 Receiver controls
THX
– Press to select a Home THX listening mode
(page 27).
STANDARD
– Press for Standard decoding and to
switch between the various
2
Pro Logic IIx and
Neo:6 options (page 26).
ADV.SURR
– Use to switch between the various
surround modes
(page 27).
STEREO
– Switches between direct and stereo
playback. Direct playback bypasses the tone controls
and any other signal processing for the most
accurate reproduction of a source (page 28).
AUTO SURR
– Selects Auto Surround (
Auto playback
on page 26).
ACOUSTIC EQ
– Press to select an Acoustic
Calibration EQ setting (page 28).
SIGNAL SEL
– Use to select an input signal (page 29).
10
MULTI OPE
Use this button to perform multi operations (page 56).
11
SHIFT
Press to access the controls outlined in white boxes (for
example,
INPUT SELECT
), or to display the currently
selected input source in the remote control LCD.
12
SOURCE
Press to turn on/off other components connected to the
receiver (see page 54 for more on this).
13 Character display (LCD)
This display shows information when transmitting
control signals.
The following commands are shown when you’re setting
the remote to control other components (see
Controlling
the rest of your system
on page 54):
SETUP
– Indicates the setup mode, from which you
choose the options below.
PRESET
– See
Selecting preset codes directly
on
page 54.
LEARNING
–
See
Programming signals from other
remote controls
on page 54.
MULTI OP
– See
Multi Operation and System Off
on
page 56.
SYS OFF
– See
Multi Operation and System Off
on
page 56.
DIRECT F
– See
Direct function
on page 56.
RENAME
– See
Renaming input source names
on
page 56.
ERASE
– See
Erasing one of the remote control button
settings on page 55.
RESET – See Resetting the remote control presets on
page 55.
READ ID – See Confirming preset codes on page 55.
14 RECEIVER
Switches the remote to control the receiver (used to
select the green commands above the number buttons
(ANALOG ATT, etc)). Also use this button to set up
surround sound (page 8, page 36).
15 VOL +/–
Use to set the listening volume.
16 MUTE
Mutes the sound or restores the sound if it has been
muted (adjusting the volume also restores the sound).
17 EFFECT/CH SEL
Press repeatedly to select a channel, then use +/– to
adjust the level (see Tip on page 42). Also adjusts the
level of the Advanced Surround effects, Dolby Pro
Logic IIx Music, and Neo:6 Music parameters
(page 27). You can then use the +/– buttons to make
these adjustments.
VSX-1016_HY.book.fm 25 ページ ２００６年２月２４日 金曜日 午前１１時５３分