Filter
Top Products
56
05
Basic playback
! If the Bluetooth wireless technology device’s security code is “0000”, there is no need to make the security code
setting on the receiver. Press ADPT to set the ADAPTER PORT input, then conduct the pairing operation on
the Bluetooth wireless technology device. If pairing is successful, there is no need to performing the pairing
operation below.
! When using the AS-BT200 only: This unit complies with Bluetooth Specifications Ver. 2.1. When this unit and
another device equipped with Bluetooth wireless technology both comply with Bluetooth Specification Ver. 2.1,
pairing of the two may be possible without the need for inputting a password.
In this case, a passcode may be displayed on this receiver and on the device equipped with Bluetooth wire-
less technology. If this happens, check that the same passcode is displayed on this receiver and the device
equipped with Bluetooth wireless technology, then press ENTER. After this, also perform the connection
operation on the Bluetooth device to be connected. If the passcode does not match the code displayed on the
Bluetooth device to be connected, press RETURN to cancel pairing, then try starting over.
Press ADPT to set the ADAPTER PORT input, then conduct the pairing operation on the Bluetooth wireless
technology device. If pairing is successful, there is no need to performing the pairing operation below.
! Pair one unit at a time.
! When connecting this receiver by Bluetooth connections with a device equipped with the Bluetooth function to
listen to music, do not connect any devices other than this receiver by Bluetooth connection to the Bluetooth-
equipped device. If a Bluetooth connection is already established with a device other than this receiver, discon-
nect the other device before connecting this receiver.
1 Press ADPT on the remote control to switch the receiver to ADAPTER PORT input.
2 Press TOP MENU to select Bluetooth Setup.
3 Use i/j to select ‘PIN’ then press ENTER.
4 Use i/j to select one of PIN codes 0000, 1234 or 8888, then press ENTER.
You can use any of 0000, 1234 or 8888 PIN codes. Bluetooth wireless technology device using any other PIN
code cannot be used with this receiver.
5 Press the RETURN button twice to exit Bluetooth Setup.
6 Switch on the Bluetooth wireless technology device that you want to make pair, place it
near the receiver and set it to the pairing mode.
7 From the Bluetooth wireless technology device list, select Bluetooth ADAPTER and enter
the PIN code selected in step 4.
8 Check to see that the Bluetooth ADAPTER is detected by the Bluetooth wireless technology
device.
If the receiver and Bluetooth wireless technology device are not paired, start over from step 6.
Note
! The PIN code may in some cases be referred to as PASSKEY.
! For information on enabling pairing on the Bluetooth wireless technology device, connection procedures, etc.,
see the Bluetooth wireless technology device’s operating instructions.
Listening to music contents of a Bluetooth wireless technology device with
your system
1 Press ADPT on the remote control to switch the receiver to ADAPTER PORT input.
! The ADAPTER PORT input can also be selected by pressing SOUND RETRIEVER AIR on the receiver. In this
case, the optimum listening mode (SOUND RETRIEVER AIR) is selected automatically.
2 From the Bluetooth wireless technology device, perform the operation to connect to the
Bluetooth ADAPTER.
! When the Bluetooth ADAPTER is not plugged into the ADAPTER PORT, No Adapter will be displayed if
ADAPTER PORT input is selected.
3 Start playback of music contents stored on the Bluetooth wireless technology device.
This receiver’s remote control buttons can be used for basic playback of files stored on Bluetooth wireless tech-
nology devices.
! Bluetooth wireless technology device should be compatible with AVRCP profile.
! Depending on the Bluetooth wireless technology device you use, operation may differ from what is shown in
the remote control buttons.
4 While listening to a source, set the remote control to the receiver operation mode, then
press ADV SURR repeatedly to select SOUND RETRIEVER AIR.
The Bluetooth
®
word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by PIONEER CORPORATION is under license. Other trademarks and trade names are those of their
respective owners.
Air Jam
Air Jam - a Pioneer-exclusive application and available for free.
Air Jam lets you connect multi compatible devices to this unit using Bluetooth wireless technology. With it, you
can make a group playlist directly on a supported device to play in your home theater through the unit. You and
your friends can add songs from your devices to the playlist. Also Air Jam lets you delete the song before anyone
has to hear it.
1 Press ADPT on the remote control to switch the receiver to ADAPTER PORT input.
2 Press TOP MENU to select Bluetooth Setup.
3 Use i/j to select ‘Air Jam’ then press ENTER.
4 Use i/j to select ‘Air Jam ON’ then press ENTER.
5 Press the RETURN button twice to exit Bluetooth Setup.
For more details of using Air Jam, access to our website.
http://pioneer.jp/product/soft/iapp_airjam/en.html