Filter
Top Products
11
<DRB1333>
En
DJ PLAYER OPERATION
Auto Cueing (*)
When a disc is loaded, when track search is performed, and when the track is changed
with the JOG MODE set to CDJ, this function operates to automatically set the
cue point immediately before the actual start of music. ☞ P. 12
The auto cue function is not supported when track is changed with the JOG MODE
set to VINYL.
÷ Turning auto cueing on and off
Pressing the TIME MODE/AUTO CUE button and holding it down for a
second or more causes auto cueing to be alternately turned on and off.
When AUTO CUE is on, the [A. CUE] indicator will be lit up.
Starting Playback
1. Insert a disc in the player.
This unit spins discs at high speeds to provide high performance. As a result,
disc loading takes a couple of seconds.
2. If auto cueing is on, press the PLAY/PAUSE button (3/8).
÷ Wait for the CUE button indicator to light up before pressing the button.
The silent portion at the beginning of the displayed track will be skipped
and playback will begin instantaneously from the first bars of the track.
Once the first track has been played, the player will automatically search for
the beginning of the next track to be played. The cueing indicator [CUE] will
light up, the PLAY/PAUSE button [3/8] indicator will flash, and the player
will then wait for the PLAY/PAUSE button (3/8) to be pressed before begin-
ning playback of the next track.
Jog dial
DISC LOADING / UNLOADING
3. Press the EJECT button (0) to remove the disc.
÷ When the EJECT button is pressed, disc rotation stops and the disc is ejected
from the loading slot.
÷ If the disc cannot be ejected with the EJECT button, insert a pin in the
forced ejection hole on the front panel of the player. ☞ P. 5
CAUTION:
Do not attempt to press a disc back into the slot when the [EJECT]
indicator appears. Pressing a disc back into the slot while the [EJECT]
indicator appears may cause the player to stop. In this case, press
the EJECT button again and wait until the [EJECT] indicator goes out
before reinserting the disc.
Label surface up
Insert straight
1. Set the rear-panel POWER switch to ON.
2. Insert a disc.
÷ Hold the disc with label surface upwards, and insert into the front panel
disc loading slot .
÷ When playing 8cm discs, be sure to install an adaptor.
÷ Only one disc can be loaded at a time. Never attempt to load more than one
disc at the same time, or attempt to load a second disc when one disc has
already been loaded.
÷ When loading a disc, do not placing any twisting force on the disc, or try to
force the disc into the slot. Also, do not attempt to interrupt or defeat the
motion of the disc when the player begins to draw a disc into the slot or to
eject a disc, since damage to the disc or player could occur.
Do not force a disc into the unit when the POWER switch is set to OFF
as this may damage the disc and the unit.
÷ AUTO CUE on/off status is stored in memory and persists even when the
power is turned off.
÷ It can change the Auto Cue level.
7 Changing the Auto Cue level
1. Hold TIME MODE/AUTO CUE button depressed for at
least 5 seconds.
÷ The display will show [–❋❋ dB].
2. Use the CUE/LOOP MEMORY button and CUE/LOOP CALL
button to change the value.
÷ Value can be set to –36dB, –42dB, –48dB, –54dB, –60dB, –66dB, –72dB,
or –78dB (default factory setting is –60dB).
÷ The level change mode can be removed if you press the TIME MODE/
AUTO CUE button or wait 15 seconds.
÷ Even if you turn the power off, the set level will remain in memory.
Functions indicated with an asterisk (*) are disabled when
the rear panel DIGITAL OUT MODE switch is set to NORMAL.
BASIC OPERATION
TIME MODE/ AUTO CUE
CUE/LOOP
MEMORY
CUE/LOOP
CALL
CUE
SEARCH
TRACK
SEARCH
PLAY/PAUSE
EJECT
1, ¡
4, ¢
6
0
PRECAUTIONS ON PLAYING CD SINGLES (8 cm/3-inch Discs)
1 When playing CD singles (8 cm/3-inch discs), always use the adapter for 8
cm/3-inch discs. Before loading the disc into the CD player, be sure to check
that it is secured properly by the catches of the adapter. If discs have been
inserted without the adapter by mistake, remove the disc immediately by
pressing the EJECT button. If the disc does not come out with one press,
press another time.
2 Use 8 cm/3-inch disc adapters labeled with the
' mark (recommended
standard product). Do not use adapters which cause the disc to idle, nor
adapters which are bent or curved.