Panasonic RQT9223-Y Stereo Receiver User Manual


 
34
RQT9223
Using the sound menu
Sound menu items
The display shown below indicates the sound menu items. Refer to each section for details.
“CH LEVEL”
“DUAL” “DRCOMP” “W. S.” “EXIT”
“BASS” “TREBLE” “BALANCE”
(
belo
w) (
below) (
below) (
page 35)
(
page 35) (
page 35) (
page 35)
Adjusting the speaker level
You can adjust the speaker levels of the center speaker, surround speakers, surround back
speakers and the subwoofer respectively.
1. Press [SOUND MENU] to enter the sound menu.
2.
Press [
e
][
r
] to select “CH LEVEL ”, and press [OK] to confirm.
3. Press [
e
][
r
] to select a speaker to adjust,
and press [OK] to
confirm.
How speakers are displayed
C : Center, LS : Surround left, RS : Surround right,
SBL : Surround back left, SBR : Surround back right,
SB : Surround back (If you connect one surround back speaker), SUBW : Subwoofer
4. Press [
e
][
r
] to adjust the le
vel, and press [OK] to confirm.
Adjustment range:
C, LS, RS, SBL, SBR, SB (If you connect one surround back speaker);
–20 dB to +10 dB
SUBW;
---
, MIN, 1 to 29, MAX
Factory setting:
C, LS, RS, SBL, SBR, SB (If you connect one surround back speaker); 0 dB
SUBW; 20
5. Press [SOUND MENU] to select “EXIT ”, and press [OK] to
finish the setting.
Press [RETURN] to return to the previous display or to cancel the setup in the halfway.
Note
• Select “
---
” to stop output from the subwoofer.
• Sound can be distorted if you raise the volume while the subwoofer level is high. Reduce
the subwoofer level if this occurs.
• When “MULTI CH PROCESSING” indicator is off, you cannot adjust speakers other than
the subwoofer.
Adjusting the bass
You can adjust the bass through this operation.
1. Press [SOUND MENU] to enter the sound menu.
2. Press [
e
][
r
] to select
BASS ”, and press [OK] to confirm.
3. Press [
e
][
r
] f
or adjustment, and press [OK] to confirm.
Adjustment range: -10 dB to +10 dB
Factory setting: 0 dB
4. Press [SOUND MENU] to select “EXIT ”, and press [OK] to
finish the setting.
Press [RETURN] to return to the previous display or to cancel the setup in the halfway.
Adjusting the treble
You can adjust the treble through this operation.
1. Press [SOUND MENU] to enter the sound menu.
2. Press [
e
][
r
] to select
TREBLE ”, and press [OK] to confirm.
3.
Press [
e
][
r
] f
or adjustment, and press [OK] to confirm.
Adjustment range: –10 dB to +10 dB
Factory setting: 0 dB
4. Press [SOUND MENU] to select “EXIT ”, and press [OK] to
finish the setting.
Press [RETURN] to return to the previous display or to cancel the setup in the halfway.
TV/VIDEO
SUB MENU
S
ENTER
Note
• If you press buttons other
than [
e
][
r
][
w
][
q
], [OK] and
[RETURN] while setting the
sound men
u, the sound menu
operation will stop. To continue
the operation, see pages 34
and 35.
SA-BX500-PP (RQT9223-Y)_En.indd 34 6/27/2008 4:06:09 PM