Filter
Top Products
35
RQT6183
Reference
≥Some distortion is normal during SEARCH.
≥Ensure that the television is connected properly. 8
≥Make sure the television is on.
≥Ensure the television’s video input setting (e.g., VIDEO 1) is correct.
≥If “This disc is PAL system. The output is sound only.” is on the television, then you have loaded a
PAL system DVD-Audio and only the audio portion of the disc can be played.
[HT95]
≥
The unit does not output video signals from the VIDEO OUT and S-VIDEO OUT terminals when the
“PROGRESSIVE OUT” indicator is on. Press [PROGRESSIVE OUT] to turn progressive out off.
≥Ensure that the unit is connected directly to the television, and is not connected through a video
cassette recorder.
≥Go to the Video menu in the ACTION screen, and change “TV Aspect” to suit your television. You
may also need to change the screen mode on the television itself. :
[HT95]
If your television cannot change the aspect when input is progressive
Press [PROGRESSIVE OUT] so the indicator goes out. Output will now be interlace.
≥Turn progressive output off. This problem is caused by the editing method or material used on the
DVD, but should be corrected if you use interlace output.
≥Check the settings in the On-Screen Menu Icons’ video menu. E
≥Adjust the horizontal position with the on-screen menu icons. E
≥The location and orientation of the antenna are incorrect. If you are using an indoor antenna,
change to an outdoor antenna. Q
≥The television antenna wire is too close to the unit. Separate the antenna wire of the television
from the unit.
Picture
Unit displays
Picture distorted.
No picture.
The picture shown on the
television is not normal.
[HT95][HT95]
[HT95][HT95]
[HT95]
There is ghosting when
progressive output is on.
Picture quality is poor.
[HT95][HT95]
[HT95][HT95]
[HT95]
The picture is off center when
using progressive output.
The picture on the television
disappears or stripes appear on
the screen.
≥Press [FL DISPLAY] to turn the display on. K
≥You inserted a disc the unit cannot play; insert one it can. 5
≥You haven’t inserted a disc; insert one.
≥You haven’t inserted the disc correctly; insert it correctly. <
≥Check and correct the speaker cord connections. 7
If this does not fix the problem, there is a power supply problem. Call 1-800-211-7262 for support.
≥The disc is dirty. Wipe it with a soft cloth. 5
≥Incorrect operation performed. Read the instructions and try again.
≥The track playing has been recorded with a nonstandard system.
≥Trouble is likely to have occurred. The number following “H” depends on the status of the unit.
Reset procedure:
Press [Í] to switch the unit to the standby mode and then back to ON. Alternatively, press [Í] to
switch the unit to the standby mode, disconnect the AC power supply cord, and then reconnect it.
≥If the service numbers fail to clear, note the service number and contact a qualified service person.
≥
A problem has occurred with the tray mechanism. The tray will open automatically. Take out the disc and close
the tray. The unit will make the disc changing noises for a few moments and then should operate normally.
Maintenance
To clean this unit, wipe with a soft, damp cloth.
≥Never use alcohol, paint thinner or benzine to clean this unit.
≥Before using chemically treated cloth, read the instructions that
came with the cloth carefully.
≥Adjust the position of the FM or AM antenna. 9
≥Use an outdoor antenna. Q
≥Turn the television off or separate it from the unit.
≥Separate the antenna from other cables and cords.
Listening to the radio
Noise is heard.
The stereo indicator flickers or
doesn’t light.
Sound is distorted.
A beat sound is heard.
A low hum is heard during AM
broadcasts.
This unit’s display is off.
“NO PLAY”
“NO DISC”
“F61”
“DVD U11”
“ERROR”
“DVD H∑∑”
∑∑ stands for a number.
“TAKE OUT DISC”
Television displays
≥Go to Display in the ACTION menus, and select “On” for “On-Screen Messages”. L
≥Press [3, 4] while the rightmost icon is highlighted to move them down. C
≥Go to Disc in the ACTION menus, and select the preferred language for “Menus”. L
No on-screen display.
On-Screen Menu Icons not
displayed or only partially
displayed on the television.
The disc’s menu is displayed in a
different language.
Before moving the unit, ensure the disc tray is
empty.
Failure to do so will risk severely damaging the disc and
the unit.