Filter
Top Products
CQ-DP153W
9
CQ-DP153W
8
POWER
REP
D•M
V
O
L
U
M
E
CLOCK
CQ-DP153W
DISP
TRACK
TUNE
LOUD
MUTE
7 8 9 10 11 12 SCAN
1
2
3
46
APM
BA
N
D
SR
C
5
P
U
S
H
S
E
L
•
M
O
N
O
/
L
O
C
D
IS
P
1234
BAND
65
E
N
G
L
I
S
H
3
E
N
G
L
I
S
H
4
POWER
REP
D•M
V
O
L
U
M
E
CLOCK
CQ-DP153W
DIS
P
TRACK
TUNE
LOUD
MUTE
7 8 9 10 11 12 SCAN
1
2
3
46
APM
BA
ND
SRC
5
P
U
S
H
S
E
L
•
M
O
N
O
/
L
O
C
TUNE
D•M
TRACK
BAND
SR
C
Radio
Radio
CD player
(When a CD is inserted.)
Manual Tuning
[lTUNE]: Higher frequency
[kTUNE]: Lower frequency
Seek Tuning
Press and hold ...
[lTUNE]: Higher frequency
[kTUNE]: Lower frequency
Tuning will automatically stop when the signals of the next broadcast station are received.
»
Radio Mode
Press [SRC] (source) to change to the radio mode.
ᕡ
Direct Memory
Your favorite FM/AM radio station can be memorized in the D
·
M button and you can call back radio stations just by
pressing the button whatever the current sound source is, even if the power is off.
Default : FM 87.5 MHz
Band
Press [BAND] to select a desired band. (➡ page 8)
Preset Station Setting
Up to 6 stations each can be saved in the FM1, FM2, FM3
and AM preset station memories.
Note: Existing saved stations are overwritten with new
stations after following this procedure.
Display Change
Press [DISP] (display) to switch to the clock display.
Frequency Clock display
Caution: To ensure safety, never attempt to preset sta-
tions while you are driving.
Manual Preset Memory
ᕡ Use manual or seek tuning to find a station.
(
➡ page 8)
ᕢ Press and hold one of the preset buttons
from
[1] to [6] until the display blinks once.
Auto Preset Memory (APM)
Press and hold [BAND] (APM: auto preset memory) for more than 2 seconds.
• The 6 stations with good reception will be automatically sared in the memory under
preset buttons from
[1] to [6].
• Once set, the preset stations are sequentially scanned for 5 seconds each.
Preset
Station
Calling
C
Press the correspon-
ding preset button
from
[1] to [6] to tune
in a preset station.
Mono/Local Selection (MONO/LOC)
MONO: Noise is significantly decreased when weak signals are received from an FM
broadcast station.
LOCAL: Only strong signals of stations are searched for in seek tuning, while at the
LOCAL OFF setting, relatively weak signals are also searched for.
• Press and hold
[SEL] (MONO/LOC) more than 1 seconds to show the status,continu-
ously hold to change the mode per 1 second. Then, release when at the desired point.
Band
Press [BAND] to change the band.
·
Press [D·M]. (Press again to cancel)
¡The direct memoried station is received.
Recalling the Direct Memory
D-M
ᕡ Select the station in Radio mode (➡ above)
Memorize
ᕢ Press and hold [D·M] until D·M indicator lights.
D-M
ᕣ Pressing continuously, frequency display will blink once and
new station will be overwritten on existing saved station.
blinks once
lights
D-M
ST
MONO
LOCAL
FM Stereo indicator
q
w
blinks once
(default)
(default)
MONO OFF / LOCAL OFF
LOCAL OFF
MONO ON / LOCAL OFF
MONO ON / LOCAL ON
MONO OFF / LOCAL ON
LOCAL ON
1 second
1 second
1 second
1 second
1 second
Press and hold ...
MONO indicator
LOCAL indicator
Regular mode
1 second
Regular mode
1 second
AM broadcasts
FM broadcasts