Filter
Top Products
38
En
Speaker Distance
Here you can specify the distance from each speaker to the
listening position so that the sound from each speaker
arrives at the listener’s ears as the sound designer
intended.
■ Unit
`feet:
Distances can be set in feet. Range: 1ft to 30ft in
1 foot steps.
`meters:
Distances can be set in meters. Range: 0.3m to 9.0m
in 0.3 meter steps.
(The default setting varies from country to country.)
■ Left, Front High Left, Center, Front High Right,
Right, Surr Right, Surr Back Right, Surr Back
Left, Surr Left, Subwoofer
`Specify the distance from the each speaker to your lis-
tening position.
Note
• Speakers that you set to “No” or “None” in the
“Speaker Configuration” cannot be selected (➔ 37).
Level Calibration
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
■ Left, Front High Left, Center
*1
, Front High Right,
Right, Surr Right, Surr Back Right, Surr Back
Left, Surr Left
`–12dB to 0dB
to +12dB in 1 dB step.
■ Subwoofer
*1
` –15dB to 0dB to +12dB in 1 dB step.
Note
• Speakers that you set to “No” or “None” in the
“Speaker Configuration” cannot be selected (➔ 37).
• Speakers that you set to “No” or “None” in the
“Speaker Configuration” do not output the test tone (➔ 37).
• The speakers cannot be calibrated while the AV receiver is
muted.
*1
For the center speaker and subwoofer, the level settings made
by using the Audio menu are saved here as the default settings
(➔ 21).
Tip
• If you’re using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
measured with C-weighting and slow reading.
Equalizer Settings
■ Equalizer
`Audyssey:
This is selected automatically by Audyssey 2EQ
Room Correction and Speaker Setup function. The
Audyssey Dvnamic Volume indicator will light
(➔ 8) and “Dynamic EQ” and “Dynamic Volume”
become available (➔ 40).
`Off
:
No Audyssey 2EQ equalizing will apply.
Note
• While the Direct or Pure Audio (European, Australian, and
Asian models) listening mode is selected, this setting has no
effect.
• Audyssey equalizing does not work for DSD sources.
Main menu Audio Adjust
With the Audio Adjust functions and settings, you can
adjust the sound and listening modes as you like.
Multiplex/Mono
■ Multiplex
This setting determines which channel of a stereo multi-
plex source is output. Use it to select audio channels or
languages with multiplex sources, multilingual TV
broadcasts, and so on.
Input Channel
`Main
:
The main channel is output.
`Sub:
The sub channel is output.
`Main/Sub:
Both the main and sub channels are output.
■ Mono
This setting specifies the channel to be used for playing
any 2-channel digital source such as Dolby Digital, or
2-channel analog/PCM source in the Mono listening
mode.
Input Channel
`Left + Right
:
Both the left and right channels are output.
`Left:
Only the left channel is output.
`Right:
Only the right channel is output.
This setting is set automatically by Audyssey 2EQ
®
Room Correction and Speaker Setup function (➔ 22).
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup function (➔ 22).
This setting is set automatically by Audyssey 2EQ
Room Correction and Speaker Setup function (➔ 22).
Audio Adjust