Filter
Top Products
13
Step 3:
Playing Back
Bass, Treble: Adjust volume of the front speaker.
r It cannot be set if the listening mode is Pure Audio
(European, Australian and Asian models) or Direct.
PM Bass (Phase Matching Bass): Suppress phase
shift in the midrange to enhance bass sound. Thus
smooth and powerful bass sound can be obtained.
r It cannot be set if the listening mode is Pure Audio
(European, Australian and Asian models) or Direct.
Subwoofer Level, Center Level: Adjust the speaker
level while listening to the sound. The adjustment you
made will be reset to the previous status when you turn
the unit to standby mode.
r The speakers cannot be adjusted if they have been
set to "No" or "None" in "Sp Config".
AccuEQ: Disables the sound field correction settings
set in the automatic speaker setting. The setting can be
separately set to each input.
r The setting cannot be selected if the automatic
speaker setting has not been performed.
r It cannot be set if headphones are connected or the
listening mode is Pure Audio (European, Australian
and Asian models) or Direct.
Late Night: Make small sounds to be easily heard. It
is useful when you need to reduce the volume while
watching a movie late night. You can enjoy the effect
on Dolby Digital, Dolby Digital Plus and Dolby TrueHD
sources only.
r Turning the unit to standby mode will set the setting
to "Off". In case of Dolby TrueHD, the setting will be
set to "Auto".
Music Optimizer : Improve the quality of the
compressed audio. Playback sound of lossy
compressed files such as MP3 will be improved. The
setting can be separately set to each input.
r The setting is effective in the signals of 48 kHz or
less. The setting is not effective in the bitstream
signals.
r It cannot be set if the listening mode is Pure Audio
(European, Australian and Asian models) or Direct.
Cinema Filter: Adjust the soundtrack that was
processed to enhance its high pitch range, in order to
make it suitable for home theater.
r
This function can be used in the following listening
modes: Multichannel, Dolby Digital, Dolby Digital Plus,
Dolby TrueHD, DTS, DTS-HD High Resolution Audio,
DTS-HD Master Audio, DTS Express, DTS 96/24,
Dolby PL II Movie, and Neo:6 Cinema.
Information: Display the audio information.
Listening Mode: Select the listening mode from the
categories of "MOVIE/TV", "MUSIC" and "GAME".
r
It cannot be set when audio is played from the TV's speakers.
6
Using the ZONE function
You can connect the unit with a pre-main amplifier in
a separate room and play the sound from the device
connected to the unit via analog connection or from the
"NET", "USB" or "BLUETOOTH" source. It is also possible
to play the sound from different analog connected devices
in the main room and separate room.
r
As for the "NET", "USB" and "BLUETOOTH", you cannot select
different inputs for the main room and separate room. For
example, if "NET" has been selected in the main room and then
"USB" is selected on the pre-main amplifier in the separate room,
the input in the main room will change to "USB" accordingly.
r
When listening to AM/FM broadcasting, you cannot select
different stations for the main room and separate room. Therefore
broadcasting of the same station will be heard in the both rooms.
Making ZONE connection
Connect the ZONE 2 LINE OUT jacks of the unit and the
line-in jacks of the pre-main amplifier in a separate room
with an analog audio (RCA) cable.
Performing ZONE playback
1.
Press ZONE2 on the remote controller, point the
remote controller at the remote controller sensor
and press
z
RECEIVER.
"Z2" lights on the unit and the ZONE function is enabled.
(ZONE 2 is now on.)
2.
Press ZONE2 on the remote controller again and
press INPUT SELECTOR of the input to be played in
a separate room.
To play the same source in the main room and separate
room, hold down ZONE2 for approximately 3 seconds.
The volume should be adjusted with the pre-main
amplifier used in the separate room.
¼
To control ZONE playback on the main unit, press ZONE2 and within 8
seconds, press the input selector button of the input to be played in a
separate room. To play the same source in the main room and separate
room, press ZONE2 twice. "Z2 : Source" appears on the unit's display.
To turn off the ZONE function: Press ZONE2 on the
remote controller and press
z
RECEIVER. Alternatively
press OFF on the main unit.
r
If ZONE 2 is on, power consumption during standby
becomes larger than normal.
r
If ZONE 2 is turned on when the listening mode of the
main room is Pure Audio, it will automatically switch to
Direct. (European, Australian and Asian models)
r
While ZONE 2 is on, the RI linked system function
(interlink between Onkyo components) is disabled.