Filter
Top Products
57
Controlling Other Components—Continued
The AV receiver’s remote controller can receive and
learn commands from other remote controllers. By trans-
mitting, for example, the Play command from your CD
player’s remote controller, the remote controller can
learn it and then transmit the exact same command when
its Play [ ] button is pressed in CD mode.
You can also use this function to learn individual com-
mands after entering a remote controller code (page 54).
Notes:
• The following buttons cannot learn new commands:
REMOTE MODE, MACRO [1], [2], [3], TV [ ],
TV CH [+]/[–], [TV INPUT], TV VOL [ ]/[ ].
• The AV receiver’s remote controller can learn approx-
imately 70–90 commands, although, this will be
reduced by commands that use a lot of memory.
• Remote controller buttons such as Play, Stop, Pause,
and so on are preprogrammed with commands for
controlling Onkyo CD players, cassette decks, and
DVD players. However, they can learn new com-
mands, and you can restore the preprogrammed com-
mands by resetting the remote controller (page 55).
• To overwrite a previously learned command, repeat
this procedure.
• Only commands from infrared remote controllers can
be learned.
• When the remote controller’s batteries expire, all
learned commands will be lost and will have to be
learned all over again, so don’t discard your other
remote controllers.
Learning Commands from Other
Remote Controllers
1
While holding down the REMOTE
MODE button for the mode in
which you want to use the com-
mand, press the [ON] button.
The Remote indicator lights up.
2
On the AV receiver’s remote con-
troller, press the button you want
to learn the new command.
10
--/---
11 12
REMOTE MODE
HDD
RECEIVER
TAPE/AMP
DVD CD
SAT
TV
VCR
CABLE
MDCDR
+
-
TV CH
TV VOL
ENTER
S
E
T
U
P
R
E
T
U
R
N
T
O
P
M
E
N
U
M
E
N
U
VOL
+
-
CH
DISPLAY
PREV
CH
DIMMER
SLEEP
MUTING
INPUT SELECTOR
32
MACRO
1
+
10 0
CLEAR
123
456
789
INPUT
I
ON STANDBY
TV
CD
V1 V2 V3
MULTI CH
DVD
TAPE
TUNER
DISC
ALBUM
1, 4
1
Remote
indicator
REMOTE MODE
HDD
RECEIVER
TAPE/AMP
DVD
CD
SAT
TV
VCR
CABLE
MDCDR
ON
3
Point the remote controllers at
each other, about 2 to 6 inches
(5–15 cm) apart, and then press
and hold the button whose com-
mand you want to learn until the
Remote indicator flashes.
If the command is learned successfully,
the Remote indicator flashes twice.
4
To learn more commands, repeat
steps 2 and 3.
Press any REMOTE MODE button
when you’ve finished.
PO
W
E
R
S
L
E
E
P
DI
M
ME
R
S
U
R
M
O
D
E
V
ID
EO
-1
V
ID
E
O
-
2
T
A
PE
D
V
D
C
D
C
D
D
VD
T
UN
E
R
T
U
N
E
R
PH
O
N
O
IN
P
U
T
S
EL
EC
TO
R
DIS
C
T
A
P
E
V
O
LU
ME
V
E
L
C
H
S
EL
PR
E
S
E
T
M
U
TIN
G
T
E
S
T
T
O
N
E
M
ULT
I-CH
INPU
T
G
R
O
U
P
R
10
--/---
11
12
REMOTE MODE
HDD
RECEIV
ER
APE/AMP
DVD
CD
SAT
VCR
CABLE
MD
CDR
+
-
T
V C
H
T
V VO
L
INP
U
T S
ELE
CT
O
R
3
2
MACRO
1
+
1
00
C
LEAR
1
2
3
4
5
6
7
8
9
INPUT
I
O
N
STA
N
DBY
T
V
CD
V1
V2
V3
MU
L
TI CH
DVD
TAPE
T
U
N
E
R
About 2 to 6
inches (5–15 cm)
RC-632M