Filter
Top Products
37
En
■Dimension
`–3 to 0
to +3
With this setting, you can move the sound field forward
or backward when using the Dolby Pro Logic IIx Music
listening mode. Higher settings move the sound field
backward. Lower settings move it forward.
If the stereo image feels too wide, or there’s too much
surround sound, move the sound field forward to
improve the balance. Conversely, if the stereo image
feels like it’s in mono, or there’s not enough surround
sound, move it backward.
■Center Width
`0 to 3
to 7
With this setting, you can adjust the width of the sound
from the center speaker when using the Dolby Pro
Logic IIx Music listening mode. Normally, if you’re
using a center speaker, the center channel sound is out-
put by only the center speaker. (If you’re not using a
center speaker, the center channel sound will be distrib-
uted to the front left and right speakers to create a phan-
tom center). This setting controls the front left, right,
and center mix, allowing you to adjust the weight of the
center channel sound.
PLIIz Height Gain
The Height Gain Control in Dolby Pro Logic IIz enables
the listener to select how much gain is applied to the front
high speakers. There are three settings, “Low”, “Mid” and
“High”, and the front high speakers are accentuated in that
order. While “Mid” is the default listening setting, the lis-
tener may adjust the Height Gain Control to their personal
preference.
■Height Gain
`Low:
Low PLIIz Height Gain becomes active.
`Mid
:
Medium PLIIz Height Gain becomes active.
`High:
High PLIIz Height Gain becomes active.
Note
•If the “Front High” setting is set to “None” (➔ 35), or “Front
High/Zone2” setting is set to “Zone2” (➔ 39), this setting is
fixed at “Mid” and does not appear.
Dolby EX
This setting determines how Dolby EX encoded signals
are handled. This setting is unavailable if no surround
back speakers are connected. This setting is effective with
Dolby Digital, Dolby Digital Plus and Dolby TrueHD
only.
■Dolby EX
`Auto:
If the source signal contains a Dolby EX flag, the
Dolby EX listening mode is used.
`Manual
:
You can select any available listening mode.
Note
• If the “SurrBack” Setting is set to “None” (➔ 35), this setting
cannot be selected.
• If the “Front High” setting is set to other than “None”, this set-
ting is fixed at “Manual” (➔ 35).
• If the “Front High/Zone2” setting is set to “Zone2” (➔ 39),
this setting is fixed at “Manual” and does not appear.
DTS Setting
Neo:6 Music
■Center Image
`0 to 2
to 5
The DTS Neo:6 Music listening mode creates 6-channel
surround sound from 2-channel stereo sources. With
this setting, you can specify by how much the front left
and right channel output is attenuated in order to create
the center channel.
Setting a value “0” in the middle is set to hear a sound.
Sound is spread in left and right (the outside) so that the
set value is made big. Please adjust by liking.
Audyssey Settings
■Audyssey
`Off
:
No Audyssey EQ™ equalizing will apply.
`On:
“Dynamic EQ” and “Dynamic Volume” become
available.
The Audyssey indicator will light (➔ 8).
Note
• Audyssey equalizing does not work for DSD sources.
■Dynamic EQ
`Off
:
Audyssey Dynamic EQ off.
`On:
Audyssey Dynamic EQ on.
The Dynamic EQ indicator will light (➔ 8).
With Audyssey Dynamic EQ™, you can enjoy great
sound even when listening at low volume levels.
Audyssey Dynamic EQ solves the problem of deterio-
rating sound quality as volume is decreased by taking
into account human perception and room acoustics. It
does so by selecting the correct frequency response and
surround volume levels moment-by-moment so that the
content sounds the way it was created at any volume
level — not just at reference level.
Note
• The setting is stored individually for each input selector.
• If Direct listening mode is selected, this setting cannot be
selected.