Filter
Top Products
8
Step 2:
Setting Up
3.
Follow the guidance displayed on the TV screen.
You can set up by viewing the guidance displayed on the
TV screen. To display the guidance, you need to make
HDMI connection between the unit and TV. Select the
item with the cursor buttons of the remote controller and
press ENTER to confirm your selection.
AccuEQ Room Calibration
Subwoofer < Yes >
[ENTER] : Next
4.
The test tones sound from the connected speaker
and automatic speaker setting starts.
The microphone measures the test tones. Measurement
will be made twice for each speaker. It takes several
minutes to be completed.
r Each speaker generates test tones at high volume
level during measurement. Keep the room as quite
as possible during measurement. Measurement
may be interrupted if there is ambient noise or radio
frequency interference. Close the window and turn off
the home appliance and fluorescent light.
r To cancel measurement on the way, disconnect the
microphone plug.
5.
When the measurement is completed, the
measurement result is displayed.
AccuEQ Room Calibration
<-Review Speaker Configuration->
Subwoofer : Yes
Front : Small
Center : Small
Surround : Small
Crossover : 150 Hz
Save
Cancel
Press
d
/
c
on the remote controller to check the settings.
Pressing ENTER when "Save" is selected will save the settings.
r The subwoofer sound may not be detected since
it is extremely low frequencies. If "No" is shown for
"Subwoofer" in the measurement result screen,
raise the subwoofer volume to around the half of
its maximum volume and make its frequency to the
maximum level.
6.
On the screen showing "AccuEQ" is "On", press
ENTER.
The settings will be applied to all the inputs.
7.
When "Please unplug setup microphone." is
displayed, disconnect the microphone.
r
If you change the speaker positions, the room furniture
layout or the number of speakers, perform automatic
speaker setting again.
r If there is an error message, follow the on-screen
instruction to remove the error cause.
3
Making Wi-Fi setting
Items to be checked before starting the procedure
Wi-Fi connection requires an access point such as
wireless LAN router (
¼
). Write down the SSID and
password (key) of the access point if they are shown
in the label of the main body. If the access point has
an automatic setting button (may be called differently
according to the manufacturer), you can set up
without inputting the password. For how to use the
automatic setting button of the access point, refer to
its instruction manual.
¼
The unit supports Wi-Fi connection with 2.4 GHz
access point.
z
Operation: You can set up by viewing the guidance
displayed on the TV screen. To display the guidance, you
need to make HDMI connection between the unit and
TV. Select the item with the cursor buttons of the remote
controller and press ENTER to confirm your selection. To
return to the previous screen, press RETURN.
1.
Start "Wi-Fi Setup".
1
Press RCV on the remote controller and then press
HOME.
2
Select "Setup" with the cursor buttons and press
ENTER.
3
Select "12. Network Setup" with the cursor buttons and
press ENTER.
r "12. Network Setup" becomes selectable after the
network starts up even if it cannot be selected first. It
may take about a minute to start up.
4
Select "Wi-Fi" with the cursor buttons and select "On" to
display "Wi-Fi Setup".
5
Select "Start" in "Wi-Fi Setup" with the cursor buttons
and press ENTER.
2.
Select the SSID of the access point to be connected
with the cursor buttons and press ENTER.
When the SSID of the access point appears on the TV
screen, select the desired access point.
r If you changed the initial setting of the access point to
skip password entry, step 4 starts automatically.
r If you changed the initial setting of the access point
to hide the SSID, see "When the access point is not
displayed".
3.
Select and set the authentication method.
Wi-Fi Setup
Please select the authentic
method.
Enter Password
Push Button
PIN code
When the screen above is displayed, select and set one
of the three authentication methods: "Enter Password",
"Push Button" and "PIN code". See below for details of
and how to set each method.
Enter Password: Enter the password of the access point to
establish connection.
1
Select "Enter Password" with the cursor buttons and
press ENTER.
2
Enter the password (
¼
) on the keyboard screen, select
"OK" with the cursor buttons and press ENTER.
r In some case, the key board screen is displayed
automatically instead of authentication screen
depending on access point device.
¼
To switch uppercase/lowercase, select "Shift" and press ENTER.
Select "Left" or "Right" and press ENTER to move the cursor to
the selected direction. Select "BS" and press ENTER to delete
the character at the left of the cursor position. To select whether to
mask the password with "*" or display it in plain text, press D on the
remote control. Press + 10 on the remote controller to enable the
"Shift" function and CLR to delete all the input characters.