38
En
Controlling Other Components
iPod/iPhone Playback via Onkyo Dock
UP-A1 Dock
With the UP-A1 Dock, you can easily play the music,
photo, or movie stored on your Apple iPod/iPhone
through the AV receiver and enjoy great sound.
You can use the AV receiver’s remote controller to
operate your iPod/iPhone.
■ System Function
Auto Power On
If you start iPod/iPhone playback while the AV receiver
is on Standby, the AV receiver will automatically turn
on and select your iPod/iPhone as the input source.
Direct Change
If you start iPod/iPhone playback while listening to
another input source, the AV receiver will automatically
select your iPod/iPhone as the input source.
Using the AV receiver’s Remote Controller
You can use the AV receiver’s remote controller to
control basic iPod/iPhone functions (➔ page 39).
■ Using Your iPod/iPhone models Alarm Clock
You can use your iPod/iPhone models Alarm Clock
function to automatically turn on your iPod/iPhone and
the AV receiver at a specified time. The AV receiver’s
input source will automatically be set to the PORT
selector.
Note
• To use this function, your iPod/iPhone must be in the UP-A1
Dock, and the UP-A1 Dock must be connected to the AV
receiver.
• This function works only in the Standard mode (➔ page 40).
• When you use this function, be sure to set the AV receiver’s
volume control to a suitable level.
• You cannot use this function for sound effects on your
iPod/iPhone.
•“UP-A1 ChargeMode” must be set to “On” to enable the Alarm
Clock (➔ page 34).
■ Charging Your iPod/iPhone models Battery
The UP-A1 Dock charges your iPod/iPhone models
battery while your iPod/iPhone is in the UP-A1 Dock
connected to the AV receiver. While your iPod/iPhone is
seated in the UP-A1 Dock, its battery will be charged
when the AV receiver is set to On or Standby.
You can specify how the power is fed to your iPod/iPhone
when the AV receiver is in Standby Mode (➔ page 34).
Note
• When UP-A1 Dock that seated iPod/iPhone is connected, the
power consumption on standby mode slightly increases.
Using the Onkyo Dock
Dock is sold separately. Models sold are different
depending on the region.
For the latest information on the Onkyo Dock
components, see the Onkyo web site at:
http://www.onkyo.com
Before using the Onkyo Dock components, update
your iPod/iPhone with the latest software, available
from the Apple web site.
For supported iPod/iPhone models, see the
instruction manual of the Onkyo Dock.
The AV receiver may take several seconds to startup, so
you might not hear the first few seconds of the first
song.
■ Operating Notes
• Functionality depends on your iPod/iPhone model and
generation.
• Before selecting a different input source, stop iPod/iPhone
playback to prevent the AV receiver from selecting the
iPod/iPhone input source by mistake.
• If any accessories are connected to your iPod/iPhone, the AV
receiver may not be able to select the input source properly.
• When connecting UP-A1 Dock to the radio tuner UP-HT1
(North American, Central American and South American
models)/UP-DT1 (European and Asian models) with
AUTO selected by the tuner’s Mode Selector switch, you can
switch the input source between UP-A1 Dock and the tuner,
by pressing PORT repeatedly on the front panel.
• While your iPod/iPhone is in the UP-A1 Dock, its volume
control has no effect. If you adjust your iPod/iPhone models
volume control while it’s in the UP-A1 Dock, make sure it’s
not set too high before you reconnect your headphones.
• The Auto Power On function will not work if you set your
iPod/iPhone in the UP-A1 Dock while it is playing.
• Do not turn off the power with the iPod/iPhone still connected
to this unit via the UP-A1 Dock.
• Set your iPod/iPhone in the UP-A1 Dock after the AV
receiver turns on.
•“UP-A1 ChargeMode” must be set to “On” to enable the
Auto Power On and Direct Change functions (➔ page 34).