Filter
Top Products
29
En
Note
•When an HDMI IN is assigned to an input selector in
“HDMI Input” (➔ page 28), this input assignment is
automatically set to the same HDMI IN. And in addition to the
usual inputs (e.g., COAXIAL, etc.), you can also select HDMI
inputs.
• Available sampling rate for PCM signals from a digital input
(optical and coaxial) is 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.
• If you connect a component (such as UP-A1 Dock that seated
iPod/iPhone) to the UNIVERSAL PORT jack, you cannot
assign any input to PORT selector.
Menu Sp Config
This section explains how to specify
which speakers are connected and their
sizes.
For speakers with a cone diameter larger
than 6-1/2 inches (16 cm), specify Large
(full band). For those with a smaller
diameter, specify Small (the default setting varies from
country to country).
The crossover frequency can be changed in the
“Crossover (Crossover Frequency)” (➔ page 29).
Note
• These settings are disabled when:
– a pair of headphones is connected, or
–the “Audio TV Out” setting is set to “On” (➔ page 35), or
–“HDMI Ctrl (RIHD)” is set to “On” (➔ page 34) and
you’re listening through your TV speakers, or
– Speakers B is on, or
– Speakers A is off.
■ Subwoofer
`Yes
:
Select if a subwoofer is connected.
`No:
Select if no subwoofer is connected.
■ Front
`Small:
`Large:
Select based on the cone diameter.
Note
•If the “Subwoofer” setting is set to “No”, this setting is fixed at
“Large” and does not appear.
■ Center
*1
, Surround
*1
`Small:
`Large:
Select based on the cone diameter.
`None:
Select if no speaker is connected.
Note
*1
If the “Front” setting is set to “Small”, the “Large” option
cannot be selected.
■ Crossover (Crossover Frequency)
This setting is advantageous for the speakers that you
specified as “Small” in the “Sp Config (Speaker
Configuration)” (➔ page 29). To get the best bass
performance from your speaker system, you need to set
the crossover frequency according to the size and
frequency response of your speakers.
`40Hz, 50Hz, 60Hz, 70Hz, 80Hz, 90Hz, 100Hz,
120Hz, 150Hz, 200Hz
(The default setting varies from country to country.)
Use the diameter of the smallest speaker in your system
when choosing the crossover frequency.
*
Choose the setting suitable for the speaker.
Note
• For a more accurate setting, look up the frequency response in
the manuals supplied with your speakers and set accordingly.
• Choose a higher crossover frequency if you want more sound
from your subwoofer.
■ Double Bass
`On
`Off
Turn this setting on to boost bass output by feeding bass
sounds from the front left, right, and center channels to the
subwoofer.
Note
• This function can be set only if the “Subwoofer” setting is set to
“Yes”, and the “Front” setting is set to “Large” (➔ page 29).
■ Wireless Front, Wireless Surr (Surround)
*1
`Yes:
The audio is output from the speakers connected to
the wireless unit.
`No
:
The audio is not output from the speakers connected
to the wireless unit.
When the wireless unit is connected to the UNIVERSAL
PORT jack on the AV receiver, you can select if you wish
to output the audio from the speakers connected to the
wireless unit.
Note
• When no wireless unit is connected to the UNIVERSAL PORT
jack on the AV receiver, this setting is not available.
*1
If the “Surround” setting is set to “None” (➔ page 29), this
setting cannot be selected.
Sp Config (Speaker Configuration)
Cone diameter
Speaker cone diameter Crossover frequency
Over 8 in. (20 cm)
40/50/60 Hz
*
6-1/2 to 8 in. (16 to 20 cm)
70/80/90 Hz
*
5-1/4 to 6-1/2 in. (13 to 16 cm) 100 Hz
3-1/2 to 5-1/4 in. (9 to 13 cm) 120 Hz
Under 3-1/2 in. (9 cm)
150/200 Hz
*
When an optional unit is connected to the
UNIVERSAL PORT jack on the AV receiver, the
speaker setting menu may appear on-screen.