Filter
Top Products
QUICK START
In case you simply cannot wait to experience the performance of your
new NAD C 245BEE Four Channel Amplier, we provide the following
QUICKSTART instructions to get you underway.
Please make all the connections to your C 245BEE with the unit unplugged.
It is also advisable to power-down or unplug all associated components
while making or breaking any signal or AC power connections.
1 Connect your speakers to the CHANNEL A (or CHANNEL B) SPEAKERS
terminals of C 245BEE.
2 Connect your Preamplier’s PRE OUT to the C 245BEE rear panel’s
CHANNEL A (or CHANNEL B) input sockets.
3 Make sure to set the following conditions: your Preamplier’s volume
level set to minimum and C 245BEE’s +12V Trigger IN switch set to “OFF”
position.
4 Connect the AC cord to the C 245BEE’s AC Mains input and then plug
into an AC outlet.
5 Switch the POWER switch on the rear panel to the “ON” setting in order
to turn the C 245BEE to standby mode. The Standby LED indicator
embedded around the bezel of the STANDBY button will illuminate
amber.
6 Press the STANDBY button to turn ON the C 245BEE. The Standby LED
indicator will turn from amber to blue.
7 Press the front panel button CHANNEL A (or CHANNEL B) to select
desired input source.
SAVE THE PACKAGING
Please save the box and all of the packaging in which your C 245BEE
arrived. Should you move or otherwise need to transport your C 245BEE,
this is by far the safest container in which to do so. We’ve seen too many
otherwise perfect components damaged in transit for lack of a proper
shipping carton, so please: Save that box!
NOTES ON INSTALLATION
Your NAD C 245BEE should be placed on a rm, level surface. Avoid
placing the unit in direct sunlight or near sources of heat and damp. Allow
adequate ventilation. Do not place the unit on a soft surface like a carpet.
Do not place it in an enclosed position such a bookcase or cabinet that
may impede the air-ow through the ventilation slots. Make sure the unit is
switched o before making any connections.
The RCA sockets on your NAD C 245BEE are colour coded for convenience.
Red and white are Right and Left audio respectively.
Use high quality leads and sockets for optimum performance and reliability.
Ensure that leads and sockets are not damaged in any way and all sockets
are rmly pushed home.
For best performance, use quality speaker leads of 16 gauge (1.5mm)
thickness or more. If the unit is not going to be used for some time,
disconnect the plug from the AC socket.
Should water get into your NAD C 245BEE, shut o the power to the unit
and remove the plug from the AC socket. Have the unit inspected by a
qualied service technician before attempting to use it again.
DO NOT REMOVE THE COVER; THERE ARE NO USERSERVICEABLE
PARTS INSIDE.
Use a dry soft cloth to clean the unit. If necessary, lightly dampen the cloth
with soapy water. Do not use solutions containing benzol or other volatile
agents.
BARE WIRES AND PIN CONNECTORS
WARNING: The terminals marked with this symbol
are hazardous live. External wiring connected to these
terminals requires installation by an instructed person or
the use of ready-made leads or cords.
Bare wires and pin sockets should be inserted into the hole in the shaft
of the terminal. Unscrew the speaker terminal’s plastic bushing until the
hole in the screw shaft is revealed. Insert the pin or bare cable end into
the hole and secure the cable by tightening down the terminal’s bushing.
Ensure bare wire from the speaker cables does not touch the back panel or
another socket. Ensure that there is only 1/2” (1cm) of bare cable or pin and
no loose strands of speakers wire.
INTRODUCTION
GETTING STARTED
5
ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ