Filter
Top Products
50
ENGLISH
RECORDING AN ANALOG SOURCE
In normal operation, the audio or video source
selected for listening through the SR6001 is sent to
the record outputs.
This means that any program you are watching
or listening to may be recorded simply by placing
machines connected to the outputs for TAPE OUT,
CD/CDR OUT and VCR OUT in the record mode.
To record the input source signal you are currently
watching or listening to
-
TUNING
PRESET
-
++
REMOTE CONTROLLER
RC5001SR
AMP
AUX2
BASS
TREBLE
AUDI O
ANGLE
SUB TITLE
DISC+
CH-SEL
V-O FF
ATT.
AUX1
MDMD
CDRCDR
CDCD
DVDDVD VCRVCR
TUNERTUNER
DSSDSS
TVTV
TAPE
1.
STANDBY
PHONES
INPUT SELECTOR
AV SURROUND RECEIVER SR6001
MENU
PURE DIRECTHT-EQ
7.1CH INPUT
MODE AUTO
MULTI
PURE DIRECT
SURROUND
SPEAK
E
MULTI
DSD
POWER ON/OFF
DISPMULTIAU TO TUNED
SLEEP
SURRDIRECT
AUTO
1.
1.
Select the input source to record by turning the
INPUT FUNCTION SELECTOR knob on the
front panel or simply press the input selector
buttons on the remote.
The input source is now selected and you may
watch or listen to it as desired.
2.
The currently selected input source signal is
output to the TAPE OUT, CD/CDR OUT and
VCR OUT outputs for recording.
3.
Start recording to the recording component as
desired.
SPEAKER A/B
DIGITAL
VIDEO
S-VIDEO
AUX 1 INPUT
VOLUME
DOWN
MultEQ
ENTER
MENU
7.1CH INPUT
MULTI
A/B
T-MODE
MEMORY CLEAR
DISPLAY
EXIT
SPEAKERS
BAND
MIC
SPEAKER
MULTI
L
C
R
SLSSR
LFE
DIGITAL
SURROUND
V-OFF
U
LTI AUTO TUNED STSPKR A B
NIGHT
PEAK ANALOG
DIGITAL
ATT
SURR DIRECT
AUTO
DISC 6.1 MTX 6.1 EQ
PCM
AAC
CAT
P
.
SCAN
CAT
789
0
+10+10
HT-EQ
MULTI/
MENU
SPKR A/B
ENTER
INFO
CH/
M-SPKR
MUTE
VOLUME
7.1CH IN
STEREO
NIGHT
M
-
CH
ST
MEMO
CL
A/DA/D
SR6001 has speaker system - A and speaker
system- B for front L/R channels.
You can select these systems by pressing
SPEAKERS A/B button on the front panel or SPKR
A/B on the remote.
SELECTING ANALOG AUDIO INPUT OR
DIGITAL AUDIO INPUT
TAPE
REMOTE CONTROLLER
RC5001SR
MD
CDR
CD
DVD
AUX2
V
C
R
TUNER
D
SS
TV
AUX1
AMPAMP
CAT
P.SCAN
CAT
456
789
0
+10+10
HT-EQ
MULTI/
SPKR A/B
CH/
M-SPKR
MUTE
VOLUME
7.1CH IN
STEREO
NIGHT
M-CH ST
MEMO
CL
A/DA/D
If you have already assigned the digital inputs, you
can temporarily select the audio input mode for each
input source as following procedures.
Press the AMP button fi rst to enter the AMP mode
then press the A/D button.
When this button is pressed, the input mode is
switched in the following sequence.
Auto → HDMI → Digital → Analog → Auto
Auto mode:
The types of signals being input to the digital and
analog input jacks for the selected input source are
detected automatically.
If no digital signal is being input, the analog input
jacks are selected automatically.
HDMI mode:
HDMI mode can be selected only when an HDMI
input has been assigned as an input source.
When “HDMI AUDIO” under PREFERENCE of the
SETUP MENU is set to “THROUGH”, the HDMI
mode cannot be selected.
Digital mode:
The input signal is fi xed to an assigned digital input
terminal.
Analog mode:
The analog input jacks are selected.
This selection is temporary and will not be stored in
memory.
To store changes to the input mode, select “1. INPUT
SETUP” from the MAIN MENU. (See page 28)
DISPLAY MODE
P.SCAN
T.MODE
123
456
789
SEND
INPUT
EX/ES
VIRTUAL
CS
dts
P.DIRECT
l/
OFF
ON
SET
STEREO
NIGHT
M-CH ST
AUTO
SURROUND
SLEEP
LEARN
LIP SYNC/
SOURCE
DISPLAYDISPLAY
BAND
PHONES
AV SURROUND RECEIVER SR6001
MultEQ
ENTER
MENU
PURE DIRECTHT-EQ
7.1CH INPUT
MODE AUTO
MULTI T-MODE
MEMORY
DISPLAY
EXIT
S
BAND
MIC
PURE DIRECT
SURROUND
SPEAKER
MULTI
DSD
L
C
R
SLSSR
LFE
DIGITAL
SURROUND
V-OFFDISPMULTIAUTO TUNED STSPKR A B
NIGHT
PEAK ANALOG
DIGITAL
ATT
SLEEP
SURR DIRECT
AUTO
DISC 6.1 MTX 6.1 EQ
PCM
AAC
You can select the display mode for the front display
of the SR6001.
To select this mode, press the DISPLAY on the
remote control or the front panel.
When this button is pressed, the display mode is
switched in the following sequence.
Input Mode → Surround Mode → Auto display OFF
→ Display OFF → Normal Mode → Input Mode
Normal Mode:
Displays the selected input function. If the function
has been renamed using the Function Rename
feature (see page 29), the renamed name appears
on the display.
Input Mode:
Displays the input mode set via the Function Input
Setup feature (see page 28).
Surround Mode:
Displays the status of the selected surround
mode.
Auto Display Off mode:
The display is off. But, if you make a change to
the unit such as the input or surround mode, the
display will show that change, then go back to off
after about 3 seconds. When changing the volume,
it is not displayed.
Display Off mode:
The display is off completely.
Note:
• Only the DISP indicator will be illuminated on the
front display in display off condition.