Filter
Top Products
43
ENGLISH
Getting Started Connections
Basic Operations Advanced Operations TroubleshootingTroubleshootingExplanation termsInformation Specifi cations Index
GRemote controlH
Symptom Cause Countermeasure Page
Set does not
work properly
when remote
control operated.
• Batteries are worn.
• You are operating outside of the
specifi ed range.
• Obstacle between main unit and
remote control.
• The batteries are not inserted
in the proper direction, as
indicated by the polarity marks
in the battery compartment.
• The set’s remote control sensor
is exposed to strong light (direct
sunlight, fl uorescent light, etc.).
• Replace with new batteries.
• Operate within the specifi ed
range.
• Remove the obstacle.
• Insert the batteries in the
proper direction, following the
polarity marks in the battery
compartment.
• Move the set to a place in which
the remote control sensor will
not be exposed to strong light.
4
4
–
4
4
GCDH
Symptom Cause Countermeasure Page
“Unsupported”
is shown on the
display even
though a CD is
loaded.
• The disc is not properly loaded. • Reload the disc. 3
Disc does not
play when
1/3
button is pressed.
• The disc is dirty or scratched. • Wipe the disc clean or replace
the disc.
3
A specifi c part
of a disc is not
played.
• The disc is dirty or scratched. • Wipe the disc clean or replace
the disc.
3
A CD-R or CD-RW
disc cannot be
played.
• The disc has not been fi nalized.
• The recording conditions are bad
or the quality of the disc itself
it poor.
• Finalize the disc then play it.
• Use a properly recorded disc.
3
–
MP3 and WMA
fi les cannot be
played.
• The fi le formats, extensions or
settings made when the disc
was created are not compatible
with this unit.
• Create discs with fi le formats,
extensions or settings
compatible with this unit.
40
GTunerH
Symptom Cause Countermeasure Page
Continuous noise
is heard when
receiving FM
programs.
• Antenna cable is not properly
connected.
• Connect the antenna cable
properly.
• Connect an outdoor antenna.
7
–
Hissing or
continuous noise
is heard when
receiving AM
programs.
• This may be noise from a TV or
interference from a broadcast
station.
• Turn off the TV.
• Change the position and
direction of the AM loop
antenna.
–
7
If a problem occurs fi rst check the following:
1. Are the connections correct?
2. Is the set being operated as described in the user guide?
3. Are the other components operating properly?
If this unit does not operate properly, check the items listed in the table below. If the problem persists,
there may be a malfunction.
In this case, disconnect the power immediately and contact your retail outlet.
GGeneralH
Symptom Cause Countermeasure Page
Set does not
operate properly.
• External noise or interference is
causing the set to malfunction.
• Reset the microprocessor. 35
Display not lit
and sound not
produced when
power switched
to on.
• Power cord not plugged in
securely.
• Check the connections on
the set's rear panel and the
connection of the power plug to
the power outlet.
10
Display lit but
sound not
produced.
• Wrong input source selected.
• Volume control set to minimum.
• MUTING is on.
• Select the appropriate input
source.
• Turn volume up to suitable level.
• Switch off MUTING.
12
12
12
Display is off. • The Dimmer setting is set to
“OFF”.
• Set to something other than
“OFF”.
13
Power turns off
suddenly and
TIMER indicator
fl ashes red.
(Flashes at 0.5
second intervals)
• Protection circuit activated due
to a rise in internal temperature.
• Core wires of two speakers
are touching each other or a
core wire is sticking out of
the terminal and touching the
set’s rear panel, activating the
protection circuit.
• Turn off the power, wait for the
set to fully cool down, then turn
the power back on.
• Place the set in a well-ventilated
location.
• First unplug the power cord,
then twist the core wires tightly
or terminate the speaker cables,
then reconnect.
6
II
5
Power turns off
suddenly and
TIMER indicator
fl ashes red.
(Flashes at 0.25
second intervals)
• Set is damaged. • Turn off the power and contact
a Marantz service center.
–
The TV sound is
not output.
• Other digital audio signals than
2 channel linear PCM cannot
be input through AUX4 IN
(OPTICAL) terminal of this unit.
• When you try to input digital
audio signals other than 2
channel linear PCM to this unit,
set the digital audio output
setting of the TV to 2 channel
PCM.
For details, see the operating
instructions of the TV.
–
Troubleshooting
Explanation terms