Filter
Top Products
27
ENGLISH
DISPLAY MODE
SURROUND
AV SURROUND RECEIVER SR3001
R
PHONES
PURE
SETUP
DIRECT
SIMPLE
AUTO
HT-EQ
MENU
ENTER
DISPLAY
MEMORY
EXIT
BAND
MODE
DISPMULTIAU TO TUNED STV
–
OFFNIGHTPEAK ANALOG
DIGITAL
ATT
SLEEP
SURR
AUTO
DIRECT DISC 6.1MTX 6.1 EQ
DIGITAL
SURROUND
AAC
PCM
L
C
R
SLSSR
LFE
S. SPEAKER B
F.DIRECT
RDS
TUNE/SEARCH
T-MODE
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN/V-OFF
7.1CH IN
STEREO
MCH-ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII EX/ES VIRTUAL
DTS
PURE DIRECT
AUTO
321
654
98
0
7
T.TONE
MENU OFF
SET UP/
You can select the display mode for the front display
of the SR3001.
To select this mode, press the DISPLAY on the front
panel or on the remote.
When this button is pressed, the display mode is
switched in the following sequence.
→ Surround Mode → Auto-display Off → Display Off
→ Input Function → Surround Mode....
In Auto display off mode, the display is off. But, if you
make a change to the unit such as input or surround
mode, the display will show that change, then go
back to off after about 3 seconds. When changing the
volume, it is not displayed.
In Display off mode, the display is off completely.
Note:
Only the DISP indicator will be illuminated on the
front display, in display off condition
OTHER FUNCTION
ATTENUATION TO ANALOG INPUT SIGNAL
DOWN
UP
VOLUME
MUTE
ATT
DISPLAY
MEMORY
CLEAR
T-MODE
EXIT
BAND
K
ANALOG
DIGITAL
ATT
EQ
DIGITAL
SURROUND
AAC
PCM
L
C
R
SLSSR
LFE
CH.SEL LIP.SYNC
PTY
SUB-T/ATT
AUDIO
INPUT/DISC+
F.DIRECT
RDS
TUNE/SEARCH
T-MODE
TREBLE
BASS
SYSTEM REMOTE CONTROLLER
RC5500SR
If the selected analog audio input signal is greater
than the capable level of internal processing, the
“PEAK” indicator will light up on the front display. If
this happens, you should press the ATT button on the
front panel or on the remote.
“ATT” indicator will be illuminated when this function is
activated. The signal-input level is reduced by about
half. Attenuation will not work with the output signal
of TAPE-OUT, CD-R/MD-OUT, VCR1-OUT and DSS/
VCR2-OUT.
This function is memorized for each individual input
source.
LISTENING THROUGH HEADPHONES
This jack may be used to listen to the SR3001’s output
through a pair of headphones. Be certain that the
headphones have a standard 1/4" stereo phono plug.
(Note that the speakers will automatically be turned off
when the headphone jack is in use.)
SURROUND
AV SURROUND RECEIVER SR3001
INPUT SELECTOR
PHONES
STANDBY
7.1CH INPUT
PURE
SETUP
DIRECT
SIMPLE
AUTO
HT-EQ
MENU
ENTE
R
MODE
DISPMULTIAUT O TUNED STV
–
OFFNIG
H
SLEEP
SURR
AUTO
DIRECT DISC 6.1MTX 6.1
POWER ON/OFF
S. SPEAKER B
Notes:
• When using headphones, the surround mode
will change to STEREO and TruSurround (TS)
headphones by SURROUND MODE button.
• The surround mode returns to the previous setting as
soon as the plug is removed from the jack.
VIDEO ON/OFF
When no video signal is connected to the SR3001
or a DVD, etc., is connected directly to your TV,
the unnecessary video circuit can be turned off by
selecting the “VIDEO OFF” setting.
To select video off, press the V-OFF button on the
remote.
CH.SEL LIP.SYNC
PTY
SUB-T/ATT
AUDIO
INPUT/DISC+
F.DIRECT
RDS
TUNE/SEARCH
T-MODE
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN/V-OFF
7.1CH IN
STEREO
MCH-ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII EX/ES VIRTUAL
DTS
PURE DIRECT
AUTO
321
654
98
0
7
T.TONE
MENU
OFF
SELECTING ANALOG AUDIO INPUT OR
DIGITAL AUDIO INPUT
F.DIRECT
RDS
TUNE/SEARCH
T-MODE
TREBLE
CHANNEL/SKIP
BASS
A/D
P.SCAN/V-OFF
7.1CH IN
STEREO
MCH-ST
MEMO
CLEAR
DISPLAY
NIGHT
CSII EX/ES VIRTUAL
DTS
PURE DIRECT
AUTO
321
654
98
0
7
T.TONE
MENU OFF
SET UP/
If you have already assigned the digital inputs, you
can temporarily select the audio input mode for
each input source with the A/D button on the remote
controller.
When this button is pressed, the input mode is
switched in the following sequence.
→ Digital Auto → Digital → Analog → Digital Auto....
In Digital Auto mode, the types of signals being input
to the digital and analog input jacks for the selected
input source are detected automatically.
If no digital signal is being input, the analog input
jacks are selected automatically.
In Digital mode, input is fi xed to an assigned digital
input terminal.
In analog mode, the analog input jacks are selected.
This selecting is temporary, so the result will not be
stored in memory.
If you need to change the input mode completely,
use INPUT setup in SETUP MENU system. (see
page 17)