6
HOOKUP DIAGRAMS
Quick Start
1. Start with the following settings on the back of the
SRM350 v2:
Turn the POWER switch off (down).
Set the CONTOUR and MIC/LINE switches out. If using
a microphone as the input to the SRM350 v2, push the
MIC/LINE switch in.
WARNING: Turn the LEVEL control
down (counterclockwise) before every
use. If not, you could be in for a star-
tling surprise, especially if the last time
you used it was with a microphone and
now you want to connect a line-level
source.
2. Connect the output from your signal source (mixing
console, microphone, preamp, or other mic- or line-lev-
el source) directly to the INPUT connector on the back
of the SRM350 v2. This is a combination XLR and 1/4"
TRS connector, and accepts balanced or unbalanced
line-level signals from mixers, preamplifiers, CD play-
ers, tape decks, etc., with the MIC/LINE switch out, and
accepts direct connections from dynamic microphones
with the MIC/LINE switch pushed in.
3. Connect the supplied AC power cord to the IEC socket
on the back of the SRM350 v2. Plug the other end into
an AC outlet properly configured with the correct volt-
age for your particular model.
4. Turn on your signal source. Make sure its Master Vol
-
ume control (if it has one) is turned all the way down.
5. Turn on the SRM350 v2 POWER switch.
6. Start the signal source, whether it be speaking into a
microphone or starting a CD player. Adjust any volume
controls on the signal source for normal operation.
7. Slowly turn up the LEVEL control on the back of the
SRM350 v2 until the desired volume is reached (and
the LIMIT light does not come on). Always wear hear-
ing protectors if you are close when it is playing at high
levels.
8. If there is no sound,
always turn down the SRM350 v2
LEVEL control before investigating. There may be a
mixer or preamplifier mute or tape switch engaged, or a
mic switch off.
SRM350 v2: STEREO OPERATION WITH A MIXER
12k/AIR100Hz
CONTOUR
(+3dB)
POWER
LIMIT
SIGNAL
LINE
MIC
LEVEL
OO
+45
+5dB
NORMAL
PARALLEL
INPUT
THRU
CAUTION: REPLACE WITH THE SAME FUSE AND RATING. DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE.
100 - 120V / 50 - 60 Hz 220W
THIS DEVICE COMPLIES WITH PART 15
OF THE FCC RULES FOR THE U.S. AND
ICES-003, FOR CANADA. OPERATION
IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
M
I
C
G
A
I
N
12k/AIR100Hz
CONTOUR
(+3dB)
POWER
LIMIT
SIGNAL
LINE
MIC
LEVEL
OO
+45
+5dB
NORMAL
PARALLEL
INPUT
THRU
CAUTION: REPLACE WITH THE SAME FUSE AND RATING. DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE.
100 - 120V / 50 - 60 Hz 220W
THIS DEVICE COMPLIES WITH PART 15
OF THE FCC RULES FOR THE U.S. AND
ICES-003, FOR CANADA. OPERATION
IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
M
I
C
G
A
I
N
Mixer or
Preamplifier
Right
Line level
Output
Left
Line level
Output
PREMIU M ANA LOG M IXER
w/ PERKIN S EQ & FI REWIR E OP TION
1 2 3 4 5
6
7
8
9
10
11
12