Filter
Top Products
IB-HT400-WM-E-122502
TROUBLE SHOOTING
Symptom
Remedy
No power
1. Is the power cord firmly plugged into the power outlet? Insert the AC power
plug securely into the power outlet. Make sure your outlet has power, you
can check this by plugging a lamp into the outlet to see if works.
2. One of the safety mechanisms may be operating. In this event, unplug the
player from the power outlet briefly and then plug it in again to reset the set.
No sound or only a very low-level
sound is heard.
Distorted sound.
1. Check that the speakers and components are connected securely and
correctly (see Page 8, 9). Also check speaker volume (see Page 22).
2. Make sure your source (DVD or other) is plugged in and operating. Also
check that components booklet, maybe you need adjust that component.
3. Make sure that you have selected the correct source on the system (DVD or other).
4. Ensure that the input settings for the TV and stereo system are correct.
5. Adjust the master volume settings on the HOME THEATERs remote.
6. Ensure the MUTE button is
not pressed on the HOME THEATER remote (If
yes, press the MUTE button again, the MUTE indicator will go off).
7. The audio or speaker connecting wires are damaged. Replace them with new ones.
The REMOTE CONTROL unit does not
work.
25
The system does not operate properly.
Double check if input & output jacks were inserted properly. Also ask a friend to
help you before calling customer service.
The sound comes from the 2 front
speakers and subwoofer only.
The input audio siginal is stereo. This set will decode and automatically play
back sound in the format that was originally input. This is normal.
No sound or only a very low-level
sound is heard from the rear speakers.
1. Make sure the Center speakers volume is set to a normal level (see Page 22).
2. Adjust the center speaker volume by pressing the volume control buttons of
the center speaker on the REMOTE (see Page 22).
3. If you are listening to a stereo broadcast, only 2 front speakers (plus the
subwoofer) will have sound.
The surround effect is difficult to hear when
playing a Dolby Digital sound track.
Depending on the digital sound input, the output signal may at times be monaural
or stereo even if the main sound track is recorded in Dolby Digital format.
Loud hum or noise is heard.
1. Check that the speakers and components are connected securely.
2. Insert all wires firmly, follow the setup pages starting on Page 7.
No sound is heard from the center
speaker.
The left and right sounds are unbalanced
or reversed.
1.
Check that the speakers and components are connected correctly and securely.
2. Adjust front balance by pressing the volume controls of the left and right
speakers on the REMOTE (see Page 22).
1. Make sure the volume control of the rear speakers are set to normal levels
(see Page 22).
2. Adjust the rear speakers volume by pressing the VOLUME control buttons
on the REMOTE.
Press the POWER button on the MAIN UNIT to turn the set ON. Then press the
POWER button on the REMOTE. The HOME THEATER may not be operating
properly due to lightning, static electricity, or some other external factors. Reset
the player by disconnecting the power plug and then re-connecting it before
calling customer service.
No buttons operate (on the main unit
and / or the REMOTE CONTROL unit).
Humming noise is heard even if the set
stopped.
This is a normal sound the cooling fan inside makes. This will stop if the power is
off. Press the POWER button on the REMOTE to put the set in STANDBY mode.
1. Check if the batteries are installed with the correct polarities ( and ).
2. If the batteries are weak or dead, replace them with new ones (size AAA).
3. Point the remote control unit at a distance of less than 20 feet from the main
unit of the HOME THEATER system.
4. Remove any obstacles between the remote control unit and remote control
sensor.
5. If the battery terminals are dirty or corroded, clean them with sandpaper.
+
Make sure your DVDs video cable is pluggged into your TV set. This Home
Theater only improves the sound of your DVD player, it does not affect the
video at all.
Your DVD player has no picture
Slight delay when switching from DVD
to TUNER input.
This is normal, as the set tries to detect stereo or 5.1 channel signals.
During DVD play, the STEREO
indicator is on.
If your DVD disc was recorded with PCM, this is normal. Press the SURROUND
button.