Filter
Top Products
89
APPENDICES ●
READING COMMAND TABLES
q Command
w Name
e Function of the command
r The format of the command is shown. When oblique lines are drawn in the 1st and 2nd columns, there is no Set
command.
t The format of the command for reading the transceiver’s current status is shown. When oblique lines are drawn in
the 1st and 2nd columns, there is no Read command.
y The format of the command output from the transceiver is shown. When oblique lines are drawn in the 1st and 2nd
columns, there is no Answer command.
u The number of command digits is shown.
i Corresponds to the parameter of the command format.
o Corresponds to the Format number in the Parameter Table. For the parameter formats, refer to the Parameter
Table {page 84}.
!0 Indicates the function of the parameter.
COMMAND TABLES
Note:
Parameters that have a Parameter Function of “NOT USED” are not supported by the TS-870S. Any character except the ASCII control
codes (00 to 1Fh) and the terminator (;) may be entered for those parameters.
1
Auto information OFF/ON
AI
AUTO INFORMATION
2
Parameter Format Parameter function
P1 32 AI NUMBER
34567891011121314
Input FunctionOutput
SetReadAnswer
1234567891011121314
123
AI
P1
AI
P1
;
AI;
4567891011121314
;
Note:
For other commands, controls whether
changing a parameter will or will not trigger
the corresponding Answer command
to be output.
Ex:
For IF, the Answer command is output
if the step frequency or RIT/XIT
frequency is changed.
1
Sets or reads AF gain.
AG
AF GAIN
2
Parameter Format Parameter function
P1 31
AF GAIN
34567891011121314
Input FunctionOutput
SetReadAnswer
1234567891011121314
123
AG
P1
;
AG;
4567891011121314
P1AG
;
1
Selects antenna connector ANT 1/ ANT 2.
AN
ANTENNA NUMBER
2
Parameter Format Parameter function
P1 33 ANTENNA
NUMBER
34567891011121314
Input FunctionOutput
SetReadAnswer
1234567891011121314
123
AN
P1
AN
P1
;
AN;
4567891011121314
;
1
Antenna Tuner THRU/IN -LINE, and tuning START/CANCEL
AC
ANTENNA TUNER CONTROL
Note:
P1 is used for Answer only.
Tuning cannot be started if P2 is in the
THRU state (If P2="0", selecting "1" for P3
does not start tuning).
P1: RX THRU/IN P2: TX THRU/IN
2
Parameter Format Parameter function
P1
P2
P3
30
30
1
TUNE THRU/IN
(Answer Only)
TUNE THRU/IN
TUNE OFF/ON
34567891011121314
Input FunctionOutput
SetReadAnswer
1234567891011121314
123
AC P2P3 ;
ACP1P2 P3 ;
AC;
4567891011121314
1
Antenna Tuner THRU/IN -LINE, and tuning START/CANCEL
AC
ANTENNA TUNER CONTROL
Note:
P1 is used for Answer only.
Tuning cannot be started if P2 is in the
THRU state (If P2="0", selecting "1" for P3
does not start tuning).
P1: RX THRU/IN P2: TX THRU/IN
2
Parameter Format Parameter function
P1
P2
P3
30
30
1
TUNE THRU/IN
(Answer Only)
TUNE THRU/IN
TUNE OFF/ON
34567891011121314
Input FunctionOutput
SetReadAnswer
1234567891011121314
123
AC P2P3 ;
ACP1P2 P3 ;
AC;
4567891011121314
q
u
i
o
!0
w
r
t
y
e