Filter
Top Products
16
Preparations
Preparing for surround sound
Speaker settings
If you selected other than "LRG" as the center speaker setting.
1 SURR YES: Surround speakers are connected to the re-
ceiver.
2 SURR NO: No surround speakers are connected to the
receiver.
9 Press the SET UP key to accept the setting.
•The receiver enters the speaker volume level adjustment mode.
•In steps 3 and 4, indications appear only for the selected
channels of the speakers that require adjusting.
Turn on the power to this receiver by pressing POWER and
ON/STANDBY key.
Select a speaker system.
1
2
3
1 Press the SET UP key to make the subwoofer setting indica-
tion (SUBW) appear.
2 Use the MULTI CONTROL to select the appropriate subwoofer
setting.
1 SUBW YES: A subwoofer is connected to the receiver.
2 SUBW NO: No subwoofer is connected to the receiver.
• The initial setting is "SUBW YES".
• When the setting "SUBW NO" is selected, the front speakers
automatically are set to "FRNT LRG" and the procedure skips to
step 5.
• When subwoofer output sound is required select "FRNT NML".
3 Press the SET UP key to accept the setting.
•The front speakers setting indication (FRNT) appears.
4 Use the MULTI CONTROL to select the appropriate front
speakers setting.
1 FRNT NML (normal): Average size front speakers are
connected to the receiver.
2 FRNT LRG (large): Large front speakers are
connected to the receiver.
5 Press the SET UP key to accept the setting.
•The center speaker setting indication (CNTR) appears.
Adjust the volume levels for the speakers.
Sit in your normal listening position and listen to the test tone. Adjust
the volume levels for the speakers until all speakers seem to be
equally loud.
1 Use the MULTI CONTROL to adjust the volume when the test
tone is being output from the speaker channel to be adjusted.
The test tone issues from the speakers for 2 seconds at a time
in the following sequence:
Lch = Cch = Rch = RS = LS = SW = Lch
•If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed. ¶
•If the speaker setting selects are changed, the speaker level
settings are reset.
2 Press the SET UP key.
•The receiver enters the mode for inputting the distance to the
speakers.
To enable you to obtain optimum enjoyment from the receiver’s
listening modes, make sure to complete the speaker settings
(subwoofer, front, center, and surround speakers) as described below.
Continued to next page
If you selected "NML" as the front speakers setting.
1 CNTR YES: A center speaker is connected to the
receiver.
2 CNTR NO: No center speaker is connected to the
receiver.
7 Press the SET UP key to accept the setting.
•The surround speaker setting indication (SURR) appears.
8 Use the MULTI CONTROL to select the appropriate surround
speaker setting.
If you selected "LRG" as the center speaker setting.
1 SURR LRG (large): Large surround speakers are con-
nected to the receiver.
2 SURR NML (normal): Average size surround speakers are
connected to the receiver.
3 SURR NO: No surround speakers are connected
to the receiver.
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
SRSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
SW
RL
SP
STEREO
STEREO
R
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
SRSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
SW
L
SP
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
SRSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
SW
RL
SP
STEREO
6 Use the MULTI CONTROL to select the appropriate center
speaker setting.
If you selected "LRG" as the front speakers setting.
1 CNTR LRG (large): A large center speaker is connected
to the receiver.
2 CNTR NML (normal): An average size center speaker is
connected to the receiver.
3 CNTR NO: No center speaker is connected to
the receiver.
The channel indication blinks while the test tone is being output.
*4967/01-/EN 3/19/01, 6:34 PM16