Kenwood VR-409 Stereo System User Manual


 
14
Preparations
Preparing for surround sound
Speaker settings
If you selected other than “LRG” as the center speaker setting.
1 SURR YES: Surround speakers are connected to the re-
ceiver.
2 SURR NO: No surround speakers are connected to the
receiver.
9 Press the SET UP or display operation 2 [Next] key to accept the
setting.
The receiver enters the speaker volume level adjustment mode.
In steps 3 and 4, indications appear only for the selected channels of
the speakers that require adjusting.
Turn on the power to this receiver by pressing POWER
(and ON/STANDBY) key(s).
Select a speaker system.
1
2
To enable you to obtain optimum enjoyment from the receiver’s listening
modes, make sure to complete the speaker settings (subwoofer, front,
center, and surround speakers) as described below.
If you selected “NML” as the front speakers setting.
1 CNTR YES: A center speaker is connected to the
receiver.
2 CNTR NO: No center speaker is connected to the
receiver.
7 Press the SET UP or display operation 2 [Next] key to accept the
setting.
• The surround speaker setting indication (SURR) appears.
8 Use the MULTI CONTROL knob or the 5/ keys to select the
appropriate surround speaker setting.
If you selected “LRG” as the center speaker setting.
1 SURR NML (normal): Average size surround speakers are
connected to the receiver.
2 SURR LRG (large): Large surround speakers are con-
nected to the receiver.
3 SURR NO: No surround speakers are connected
to the receiver.
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
SW
RL
SP A
STEREO
1 Press the SETUP key to make the subwoofer setting indication
(SUBW) appear.
When you operate on the remote control unit
1 Press the display operation 2 [Menu] key repeatedly until
01.IR” appears in the display of the remote control unit.
2 Press the 5/ keys to select “02.Surround”, then press the
display operation 2 [Enter] key.
(SUBW) appears in the display of the unit.
2 Use the MULTI CONTROL knob or the 5/ keys to select the
appropriate subwoofer setting.
1 SUBW YES: A subwoofer is connected to the receiver.
2 SUBW NO: No subwoofer is connected to the receiver.
• When the setting "SUBW NO" is selected, the front speakers automati-
cally are set to "Large" and the procedure skips to step 5.
>02.Surround
>01.IR
Home Enter
SetUp
Home Next
3 Press the SET UP or display operation 2 [Next] key to accept the
setting.
•The front speakers setting indication (FRNT) appears.
4 Use the MULTI CONTROL knob or the 5/ keys to select the
appropriate front speakers setting.
1 FRNT NML (normal): Average size front speakers are
connected to the receiver.
2 FRNT LRG (large): Large front speakers are connected
to the receiver.
5 Press the SET UP or display operation 2 [Next] key to accept the
setting.
•The center speaker setting indication (CNTR) appears.
6 Use the MULTI CONTROL knob or the 5/ keys to select the
appropriate center speaker setting.
If you selected “LRG” as the front speakers setting.
1 CNTR NML (normal): An average size center speaker is con-
nected to the receiver.
2 CNTR LRG (large): A large center speaker is connected to
the receiver.
3 CNTR NO: No center speaker is connected to the
receiver.
Continued to next page
Display operation 1
Display operation 2
MULTI CONTROL
SETUP
5/∞
POWER
ON/STANDBY
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND
AUTO
LFE
C
S
RSLS
TI.VOLB
CLIP MUTE
RDS EON PTY
TP TA NEWS
SW
RL
SP A
STEREO