Kenwood KRF-V7090D Stereo System User Manual


 
18
EN
ENGLISH
8 Use the MULTI CONTROL knob or MULTI %/ to select the
appropriate Surround Speaker setting.
If you selected “FRNT LARGE” as the Front Speaker setting,
1 SURR NORMAL : Average size Surround Speakers are con-
nected to the receiver.
2 SURR LARGE : Large size Surround Speakers are
connected to the receiver.
3 SURR OFF : Surround Speaker setting mode to the
receiver is OFF.
If you selected “FRNT NORMAL” as the Front Speaker setting,
1 SURR NORMAL : Average size Surround speakers are
connected to the receiver.
2 SURR OFF : Surround speaker setting mode to the
receiver is OFF.
When the setting “SURR OFF” is selected, the procedure skips
to step !.
9 Press the
key or MULTI # key again to accept the setting.
The Surround Back Speaker setting indication “SB” appears.
0 Use the MULTI CONTROL knob or MULTI %/ keys to select
appropriate Surround Back Speaker setting.
If you selected “SURR LARGE” as the Surround Speaker
setting,
1 SB NORMALx1 : A single average size Surround Back
Speaker is connected to the receiver.
2 SB NORMALx2 : A pair of average size Surround Back Speak-
ers are connected to the receiver.
3 SB LARGEx1 : A single large size Surround Back Speaker
is connected to the receiver.
4 SB LARGEx2 : A pair of large size Surround Back Speak-
ers are connected to the receiver.
5 SB OFF : Surround Back Speaker setting mode to
the receiver is OFF.
L
SL S SB SR
CR
SP MUTE
AB CLIP
SW
LFE
STEREO
If you selected “SURR NORMAL” as the Surround Speaker
setting,
1 SB NORMALx1 : A single average size Surround Back
Speaker is connected to the receiver.
2 SB NORMALx2 : A pair of average size Surround Back Speak-
ers are connected to the receiver.
3 SB OFF : Surround Back Speaker setting mode to
the receiver is OFF.
! Press the
key or MULTI # key again to accept the setting.
The Subwoofer remix setting indication “SW RE-MIX” appears.
@ Use the MULTI CONTROL knob or MULTI %/ keys to select
the appropriate Subwoofer re-mix setting.
1 SW RE-MIX ON : Subwoofer re-mix setting mode to the
receiver is ON.
2 SW RE-MIX OFF : Subwoofer re-mix setting mode to the
receiver is OFF.
If Subwoofer is turned off or “FRNT NORMAL” is selected at the
Front Speaker setting, Subwoofer re-mix setting is not visible.
# Press the SETUP key again to return to the main setup
displays.
4
Select the CROSSOVER frequency.
CROSSOVER function is to adjust the receiver’s audio output character-
istics with the speakers’ characteristics which differs depending on the
size of the speakers. You will be able to enjoy a more natural and
dynamic sound experience even with small size speakers.
1 Press the
/ keys
or MULTI
@/# keys to select the CROSS-
OVER and press the SETUP key.
2 Use the MULTI CONTROL knob or MULTI %/ keys to select
the CROSSOVER frequency.
1 FREQ. : 40Hz
2 FREQ. : 60Hz
3 FREQ. : 80Hz
4 FREQ. : 100Hz
5 FREQ. : 120Hz
6 FREQ. : 150Hz
LR
SP MUTE
AB CLIP
STEREO
CROSSOVER
function will not be available when “LARGE” is
selected for all the speakers and “SW RE-MIX OFF” is selected
in step 3.
3 Press the SETUP key again to return to the main setup displays.
5
Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
The receiver enters the speaker volume level adjustment mode.
Indicators appear only for the channels of the speakers selected
in step 3.
1 Press the
/ keys or MULTI @/# keys to select the TEST TONE.
2 Press the SETUP key for the following displays:
1 T.TONE AUTO
2 T.TONE MANUAL
3 The selection of AUTO/MANUAL TEST TONE is done by the
MULTI CONTROL knob or MULTI %/ keys.
Press the SETUP key again to begin TEST TONE.
Use the MULTI CONTROL knob or MULTI %/ keys to adjust
the volume level of the test tone output from the speaker
channel to be adjusted.
For AUTO selection, the test tone is heard from the speakers in
the following sequence for 2 seconds each starting from the
Front Left speaker.
LEFT CNTR RIGHT
SR
SL
SBLSUBW
SBR
If you have selected “SB NORMALx1” or ”SB LARGEx1”,
“SBR” and “SBL” are not appeared but “SB” is appeared on the
Display.
The channel indication blinks while the test tone is being output.
L
SL SB SR
CR
SP MUTE
AB CLIP
SW
LFE
If the speaker setting selects are OFF, the speaker level
settings are reset.
For MANUAL selection, press the
/ keys
or MULTI
@/#
keys each time to select the speaker channel.
4 Press the SETUP key again.
The test tone is turned off and return to the main setup displays.
Preparing for surround sound
05.2.8, 11:57 AM18