Filter
Top Products
75
To change the transmittable signals for
operating another manufacturer’s CATV
converter and DBS tuner
1. Set the TV operation mode selector to
“CATV/DBS.”
2. Press and hold TV/CATV/DBS
(STANDBY/ON).
3. Press TV/DBS.
4. Enter a manufacturer’s code using
buttons 1–9, and 0.
See page 77 to find the code.
5. Release TV/CATV/DBS (STANDBY/ON).
After setting the TV operation mode selector to “CATV/DBS,”
you can turn on and off the CATV converter or the DBS tuner:
TV/CATV/DBS
(STANDBY/ON)
: Turns on or off the CATV
converter or DBS tuner.
After pressing TV/DBS (with TV operation mode selector set to
“CATV/DBS”), you can perform the following operations on the
CATV converter or on the DBS tuner:
CHANNEL +/– : Changes the channels.
1–10, 0, 100+ (+10) : Selects the channels.
Number button 10 will function as
the ENTER button if your equipment
requires pressing ENTER after
selecting a channel number.
Note:
Refer to the manual supplied for your CATV converter or DBS
tuner.
6. Try to operate your CATV converter
or DBS tuner by pressing TV/CATV/
DBS
(STANDBY/ON).
When your CATV converter or DBS tuner turns on or off, you
have entered the correct code.
If more than one code is listed for your brand of CATV
converter or DBS tuner, try each one until the correct one is
entered.
Note:
You cannot preset the signals for both the CATV converter and DBS
tuner at the same time.
To change the transmittable signals for
operating another manufacturer’s VCR
1. Press and hold VCR 1
(STANDBY/ON).
2. Press VCR 1.
3. Enter a manufacturer’s code using
buttons 1–9, and 0.
See page 77 to find the code.
4. Release VCR 1 (STANDBY/ON).
The following button can be used for operating the VCR :
VCR 1 (STANDBY/ON)
: Turns on or off the VCR.
After pressing VCR 1, you can perform the following operations
on the VCR:
1–10, 0, 100+ (+10) : Selects the TV channels.
Number button 10 will function as
the ENTER button if your VCR
requires pressing ENTER after
selecting a channel number.
PLAY : Starts playback.
REW : Rewinds a video tape.
FF : Fast-winds a video tape.
STOP : Stops operation.
PAUSE : Pauses playing.
¶ REC : Press this button together with the PLAY
button to start recording (only for Zone 1
operation).
Press this button together with the PAUSE
button to enter recording pause (only for
Zone 1 operation).
CHANNEL +/– : Changes the TV channels on the VCR.
Note:
Refer to the manual supplied for your VCR.
5. Try to operate your VCR by pressing
VCR 1
(STANDBY/ON).
When your VCR turns on or off, you have
entered the correct code.
If more than one code is listed for your brand of VCR, try
each one until the correct one is entered.
VCR1
Remote’s display
EFFECT
LIVENESS
FM MODE
RETURN
100
+
123
456
7
/P
89
10
+
100
VCR 1
STANDBY/ON
TV
CATV/
DBS
Remote’s display
TV/CATV/DBS
STANDBY/ON
TV/DBS
EFFECT
LIVENESS
FM MODE
RETURN
100
+
123
456
7
/P
89
10
+
100
TV/CATV/DBS
STANDBY/ON
VCR 1
STANDBY/ON
68-84_RX-DP15B[J]f.pm6 04.3.15, 9:14 PM75