Filter
Top Products
42
7
DUAL MONO
Select the playback sounds (channel).
MAIN : Select to play back the main channel (Ch 1).*
1
Signal indicator “L” lights up while playing back
this channel.
SUB : Select to play back the sub-channel (Ch 2).*
1
Signal indicator “R” lights up while playing back
this channel.
ALL : Select to play back both the main and sub-channels
(Ch 1/Ch 2).*
1
Signal indicators “L” and “R” light up while playing
back these channels.
Notes:
• The Dual Mono format is not identical with bilingual
broadcasting or the MTS (Multi-channel TV Sound) format used
for TV programs. So this setting does not take effect while
watching bilingual or MTS programs.
*
1
Dual Mono signals can be heard from the following speakers—
L (left front speaker), R (right front speaker), and C (center
speaker)—with respect to the current Surround setting.
9 Setting the Digital Input/Output Terminals
—DIGITAL IN/OUT
When you use the digital input
and output terminals on the rear,
you have to register what
components you have connected
to these digital terminals.
7
COAX IN 1/2/3, OPT IN 4/5/6
Select the name of the component connected to each digital
terminal so that it will correspond to the source selecting button
on the unit and on the remote control.
• Each time you press # or @ (RIGHT or LEFT), the
component name changes as follows:
DVD “ CD “ TV (or DBS*
2
) “ CDR “ MD “
VCR1 “ (back to the beginning)
Notes:
• If you have selected the same source for different terminals,
only the last performed terminal setting will be valid. (The other
terminal settings will be automatically set to “OFF.”)
*
2
If you have changed the source name from “TV” to “DBS,” “DBS”
appears (see page 27).
6 Setting the Surround Channel Output
Speakers—SURR CH OUT
On this submenu screen, you can
preset which surround speakers
to use for 5.1 channel
reproduction.
Note:
This submenu is not available in the following cases:
– When “SURR BACK OUT” is set to “1SPK” on the SPEAKER
SETTING submenu,
–“SURR BACK SP” is set to “NONE” on the SPEAKER SETTING
submenu,
–“SPEAKER 2” is set to “BI-AMP OUT” on the ZONE 2/SPEAKER 2
submenu, or
– When the Zone 2 speakers are activated.
7
SURROUND SP
Select the surround channel output speakers from the following:
SURR : Select to use the left and right surround
speakers—recommended setting for Dolby
Pro Logic and Pro Logic II.
SBACK : Select to use only the surround back speakers.
SURR+SB : Select to use both the surround speakers and
surround back speakers.
7 Setting the Audio Delay Level—AUDIO DELAY
Synchronization between audio
and video reproduction can be
possibly disturbed because
video signal decoding is time-
consuming compared to the
audio signal decoding.
On this submenu screen, you can correct synchronization between
video and audio signals by delaying the audio signal timing.
7
AUDIO DELAY
Adjust the delay time within the range of 0 ms (initial setting:
no effect) to 200 ms (maximum) in 20 ms intervals.
8 Selecting the Dual Mono Sound—DUAL MONO
On this submenu screen, you can
select the playback sound
(channel) you want while
playing digital software recorded
(or broadcast) in the Dual Mono
mode, which includes two
monaural channels separately.
SURR CH OUT
SURROUND SP: SURR
:OPERATE
:BACK
Continued on the next page.
Without Surround With Surround Activated
Center speaker setting
LARGE/SMALL NONE
L R L C R L R
MAIN Ch 1 Ch 1 — Ch 1 — Ch 1 Ch 1
SUB Ch 2 Ch 2 — Ch 2 — Ch 2 Ch 2
ALL Ch 1 Ch 2 — Ch 1+Ch 2 — Ch 1+Ch 2 Ch 1+Ch 2
Dual Mono
Setting
DIGITAL IN/OUT
COAX IN 1 : DVD
COAX IN 2 : CD
COAX IN 3 : TV
OPT IN 4 : CDR
OPT IN 5 : MD
OPT IN 6 : VCR1
DIGITAL OUT :THROUGH
:OPERATE
:BACK
AUDIO DELAY
AUDIO DELAY : 0ms
:OPERATE
:BACK
DUAL MONO
DUAL MONO : MAIN
:OPERATE
:BACK
35-44_RX-DP15B[J]f.pm6 04.3.15, 9:20 PM42