JVC CA-MXJ777V Stereo System User Manual


 
11
English
Program Play
Random Play
Continuous Play
3
Press one of the disc number buttons
(CD 1, CD 2, and CD 3) r, 1 to
select the disc number you want to
play.
CD
1
CD
2
CD
3
Track number
PROGRAM
2 31
Program step number
Disc number
4
Select a track from the CD selected in the above
step.
On the unit:On the unit:
Press 4 ; or ¢ ; to select the track number, then press
SET k.
On the remote control:On the remote control:
Press the number buttons &.
For how to use the number buttons,
see “To go to another track directly
using the number buttons” described
to the left.
PRESET
SET
SEA CONTROL
To locate a particular point in a track
During play, press and hold 1 x or ¡ x.
1: Fast reverses the disc.
¡: Fast forwards the disc.
When using the remote control, press and hold
1 / 4 0 or ¢ / ¡ (.
To go to another track
Press 4 ; or ¢ ; repeatedly before or during
playback.
4: Goes back to the beginning of the current
or previous tracks.
¢: Skips to the beginning of the next or
succeeding tracks.
When using the remote control, press 1 / 4 0
or ¢ / ¡ ( during or before playing.
If you press and hold
44
44
4
/
¢¢
¢¢
¢
;
(or
11
11
1
/
44
44
4
00
00
0
or
¢¢
¢¢
¢
/
¡¡
¡¡
¡
(
before playing)
You can change the tracks continuously.
To go to another track directly using the number buttons
Pressing the number button(s) & before or during play allows you
to start playing the track number you want.
Ex.: For track number 5, press 5.
For track number 15, press +10,
then 5.
For track number 20, press +10,
then 10.
For track number 32, press +10,
+10, +10 then 2.
Programming the Playing Order of the Tracks —
Program Play
You can arrange the order in which the tracks play before you start
playing. You can program up to 32 tracks.
To use Repeat play (see page 12) for Program play, press REPEAT
n after starting Program play.
1
Load discs.
If the current playing source is not the CD player, press CD
6 y, _ , then 7 z, + before going to the next step.
2
Press PROGRAM/RANDOM v button
repeatedly until “PROGRAM”
appears on the display.
TUNING
PRESET
PREV
NEXT
PROGRAM
2 31
Each time you press the button, CD play mode changes as
follows:
PROGRAM
2 31
13
5
Program other tracks you want.
To program tracks from the same disc, repeat step 4.
To program tracks from a different disc, repeat steps 3 and 4.
6
Press CD 6 y, _.
The tracks are played in the order you have programmed.
To stop during play, press 7 z, +.
To exit from Program play mode, press PROGRAM/
RANDOM v repeatedly again before or after play so that the unit
enters another play mode. (The program you have made is stored in
memory until you erase the program.)
If a program has been stored in memory, the program is called
up.
Continued
PROGRAM
/ RANDOM
CENTER MODE
DELAY TIME
PRO LOGIC 3 STEREO TEST TONE
CENTER
LEVEL
REAR
LEVEL
BALANCE
+
+
RL
CENTER MODE
DELAY TIME
PRO LOGIC 3 STEREO TEST TONE
CENTER
LEVEL
REAR
LEVEL
BALANCE
+
+
RL
EN6-17;MX-J777V/PM6 7/8/99, 9:16 AM11