Filter
Top Products
23
Insignia NS-AV511 Surround Sound Receiver
www.insigniaproducts.com
When enabling the HDMI Through function,
regardless of whether the AV receiver is On or in
Standby, both the audio and video streams from an
HDMI input will be output to the TV or other
components via the HDMI connection. The HDMI
THRU and HDMI indicators light when this is
enabled. This setting is set to Auto automatically
when the above CEC Function is set to On.
Audio TV OUT (Audio TV Out submenu)
This setting determines whether audio received by
HDMI IN is output by the HDMI OUT. You may want
to turn this preference on if your TV is connected to
the HDMI OUT and you want to listen to the audio
from a component that’s connected to an HDMI IN,
through your TV’s speakers. Normally, this should
be set to Off.
Audio Return Ch (ARC)(Audio Return Ch submenu)
The audio return channel (ARC) function enables an
HDMI 1.4-capable TV to send the audio stream to
the HDMI OUT jack of the receiver. To use this
function, you must select the TV/CD input and your
TV must support the ARC function.
LipSync (LipSync submenu)
Lets you set the receiver to automatically correct
any delay between the video and the audio, based
on the data from the connected monitor.
• To enable, set to ON.
• To disable, set to OFF.
Changing audio settings
You can change various audio settings by pressing
HOME on the remote control.
To change audio settings:
1 Press RECEIVER on the remote control, then
press HOME.
2 Press or to select an option, then press
or to change the setting. Repeat this step
to change additional settings.
Changing tone control settings
You can adjust the bass and treble for the front
speakers, except when the Direct Listening mode is
selected. Options include:
• Bass–You can boost or cut low-frequency
sounds output by the front speakers. 10 dB to
0 dB to +10 dB, in 2 dB steps
• Treble–You can boost or cut high-frequency
sounds output by the front speakers. 10 dB to
0 dB to +10 dB, in 2 dB steps
Note
Changing the speaker levels
You can adjust the volume of each speaker while
listening to an input source. These temporary
adjustments are cancelled when the receiver is set
to Standby. To save the setting you made here, go
to “Setting the level calibration (Level Cal menu)”
on page 15, before returning the receiver to
Standby. Options include:
• Subwoofer–15 dB to 0 dB to +12 dB, in 1 dB
steps.
• Center–12 dB to 0 dB to +12 dB, in 1 dB
steps.
Note
Notes
• Only the input source assigned to the HDMI IN
via “HDMI Input” is enabled.
• The power consumption during standby mode
will increase when the HDMI Through function
is turned on, however, in the following cases,
the power consumption does not increase:
• The TV is in standby mode.
• You are watching a TV program.
• Refer to the connected component’s instruction
manual for details.
• Depending on the connected component, the
correct input source may not be selected with
the setting set to Auto.
• This setting is set to Off automatically when CEC
Function is set to Off.
Notes
•If On is selected and the signal can be output by
the TV, the receiver outputs no sound through
its speakers.
•If On is selected, TV Sp On appears on the
display when you press DISPLAY.
• When TV Control is set to On, this setting
default is Auto.
• With some TVs and input signals, no sound may
be output, even when this setting is On.
• When the Audio TV OUT or TV Control are set
to On, and you are listening through your TV’s
speakers, if you turn up the receiver’s volume
control, the sound is output by the receiver’s
front left and right speakers. To stop the
receiver’s speakers from producing sound,
change the settings, change your TV’s settings,
or turn down the receiver’s volume.
Notes
•The Audio Return Ch setting can only be set
when HDMI Control is On.
• This setting is set to Auto automatically when
HDMI Control is set to On first time.
Notes
• This function only works if your
HDMI-compatible TV supports HDMI Lip Sync.
• You can check the amount of delay being
applied by the HDMI Lip Sync function on the
A/V Sync screen.
Note
When Audio TV OUT is set to On, the HOME button
is disabled.
Notes
• To bypass the bass and treble tone circuits,
select the Direct listening mode.
• This procedure can also be performed on the
receiver by pressing the TONE–/+ buttons.
Notes
• You cannot use this function while the receiver
is muted.
• Speakers that are set to No or None in the Sp
Config (Speaker Configuration) submenu
cannot be adjusted.
NS-AV511_11-0201_MAN_.book Page 23 Wednesday, April 13, 2011 9:31 AM